Multiquip manual WM63H5/WM63H8/WM63E Plaster And Mortar Mixers, Table of Contents

Page 4

Table of Contents

WM63H5/WM63H8/WM63E Plaster And Mortar Mixers

Proposition 65 Warning	2
Silicosis/Respiratory Warnings	3
Table Of Contents	4
Parts Ordering Procedures	5
Safety Information	6-10
Safety Chain Connection	11
Specifications	12
Dimensions	13
General Information	14
Components	15
Inspection	16-17
Basic Engine	18
Electric Motor	19-20
Paddle Blade Adjustment	21
Start-Up	22-23
Operation	24
Maintenance (Engine)	26-27
Maintenance (Mixer)	28-33
Troubleshooting	34-36
Wiring Diagram	37
Explanation Of Code In Remarks Column	38
Suggested Spare Parts	39

Component Drawings

Nameplate And Decals	40-41
Frame Assembly	42-43
Paddle Shaft Assembly	44-45
Steel Tub Assembly	46-47
Drum And Paddle Shaft Complete Assembly....	48-49
Axle Assembly	50-51
Engine Assembly	52-53
Electric Motor Assembly	54-55
Cabinet Assembly	56-57
Terms And Conditions Of Sale — Parts	56

NOTICE

Specifications and part numbers are subject to change without notice.

page 4 — wm63-series Mixer • operation and parts manual — rev. #0 (09/27/12)

Image 4

Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WM63H5/WM63H8/WM63E Plaster And Mortar MixersChoose from three easy options Safety information SaFeTY messagesExplosive fuel hazards Burn hazardsGeneral saFeTY Engine saFeTY gasoline models onlY Mixer saFeTYBefore servicing equipment Fuel saFeTY gasoline models onlY GeneraTor saFeTYEleCTriC moTor saFeTY eleCTriC models onlY Power Cord/Cable safetyEnvironmenTal saFeTY Towing saFeTY„ alwaYs shutdown engine before transporting Safety chain connection Tow Bar to Mixer ConnectionSpecifications Mixer SpecificationsDimensions DimensionsGeneral information Components Mixer ComponentsInspection Before StartingEngine Oil Check Fuel CheckBelt Check Start/Stop SwitchGrease Fittings Dumping Mechanism Basic engine Initial ServicingElectric Motor Electric motorElectric Motor Connection Electric Motor Voltage Switch Recommended Extension Cord SizesPaddle blade adjustment Adjust paddles as shown in FigureTurn the engine switch to the on position Start-upBelt Slip Lever Start/Stop Position Operation Mixing/DumpingStopping the Mixer Gasoline Stopping the Mixer electric motorPage Maintenance engine First EveryInstall drain bolt with sealing washer and tighten securely Engine air cleanerEngine oil Maintenance Mixer Ball Socket and Clamp Face MaintenanceDrum Head Seals Drum Bearing Bracket LubricationMain Gear and Drive Pinion Alignment Wheel BearingsInspectTooth Contact between Main Gear and Drive Pinion Grease Fittings Zerk Maintenance Electric Motor Gear LubricationTires/Wheels/Lug Nuts Tires Wear/InflationStart all wheel lug nuts by hand Lug Nut Torque RequirementsNever use an pneumatic air gun to tighten wheel lug nuts Mixer Cleaning SuspensionMixer Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Adjust if necessary Drum difficult to discharge tilt Blades adjusted too tightReplace seals Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionSafety Instructions Nameplate and decalsPart Name QTY Remarks 521232 Decal, inspect before towingFrame assy 514842 491692530023 507444Paddle shaft assy 514752 492584 NUT, Lock 1/2 530140C3215 SCREW, HHC 1/2-13 X 3-1/2 EM200292 530141Steel tub assy Part Front Frame Rear Frame530028 324920561-001 491008Drum and paddle shaft complete assy 516069 EM969013 NUT, Lock 3/8 301909207594-012 Roll PIN 3/16 X 3/4 20654-001 EM961019Axle assy 3469 29194516476 8164Engine assy EM905016 492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25513868 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226Electric motor assy 492378 Bolt 3/8 X 1-3/4 G5 20216-001 20061-001492582 NUT, Nylon 5/16-18 35L229S302 502213Cabinet assy 112515014 49020213287 2203Terms and conditions of sale parts FreigHT poliCYPage HERE’S HOW to GET Help