Peavey 3D Mix Pro Booth Level, Mono Level, Headphone Cue Level, Headphone Pan, Headphone Level

Page 9

28. Booth Level

Use this control to adjust the stereo Booth Output (9) level. Adjusting this control fully clockwise will result in maximum signal level. This output is usually used for local monitoring when headphones are not convienient.

29. Mono Level

Use this control to adjust the Mono Out (4) level. Adjusting this control fully clockwise will result in maximum signal level. This output is a sum of the left and right main signals (prefader), and can be used to drive a lighting system or subwoofer crossover EQ and amp.

30. Headphone Cue Level

Use this control to set the level of the cue material present in the Headphone and Booth Outputs. With the Headphone Select switch (33) set to Normal, adjust this control to a comfortable level and the Headphone Pan (31) fully counterclockwise to listen to the cue signal in the headphones. The Headphone Cue Level control should be set in conjunction with the Headphone Pan control to achieve the desired headphone mix.

31. Headphone Pan

Use this control to pan the material in the headphoneÕs between cue and mains while the Headphone Select switch (33) is in the Normal position. Increasing one signal level will reduce the other. While the switch is in the Split position, the Headphone Pan control will not function.

32. Headphone Level

The Headphone Level control is the master volume control for the Headphone Output (34). Adjusting this control fully clockwise will result in maximum signal level at the output.

33. Headphone Select

This switch is used to change the headphoneÕs operational mode. When placed in the ÒNormalÓ position, stereo monitoring of the cue and/or main material is determined by the Headphone Pan (31). As you pan between the cue and main signals, you will hear both signals in the left and right headphone cups. When the Headphone Select switch is in the ÒSplitÓ position, the left cup contains the cue material and the right cup contains the main material. To adjust the level in this mode, use the Cue Level control (30) to set the preferred balance and the Headphone Level control (32) to set the overall level.

34. Headphone Output

This 1/4" stereo output jack is used to power a set of stereo headphones. The tip is wired left, the ring is wired right, and the sleeve is wired to ground.

35. Stereo Output Level Indicator

 

 

This calibrated pair (L and R) of 12 segment LED meters

 

 

 

35

illuminates to visually indicate program output levels. At the

 

 

top of each meter is a clip LED to notify you of extreme

 

 

 

 

levels and possible distortion caused by overdriving the

 

 

 

signal.

 

 

 

 

 

36. X-Fader

Remove these screw to

replace the X-Fader.

This 45 mm stereo slider delivers crossfade

 

 

 

 

 

 

 

 

 

 

capability between Channels 1 and 2. Adjusting

 

 

 

 

 

 

 

 

 

 

this slider from its maximum left position to its

 

 

 

 

 

 

36

 

 

 

 

 

 

 

maximum right position will pan the main output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

from being completely Channel 1 to completely Channel 2. The interim from left to right produces a combination of both, allowing a smooth transition from one channel to the other. NOTE: The X-Fader is replaceable by removing the two outside mounting screws on the top of the unit. Once the screws have been removed, the slider can be pulled out and replaced with ease.

9

Image 9
Contents 3D Mix Pro Page Two Microphone Inputs Features per input Two Distinct Stereo Input Channels Features per channelMaster Section Master mic featuresMain Outputs Back Panel Power and GroundingEffects SEND/RETURN Monitor OutputsInput Channels 1 InputsCONTROLS/INDICATORS Master Section MIC Inputs and ControlsStereo Output Level Indicator Booth LevelMono Level Headphone Cue LevelEffects Effects Loop ControlsSpatial Expander HUM and Noise 22 Hz 22 kHz BW 3D MIX PRO SpecificationsStereo Channel EQ +12 dB, -22dB MIN Input Levels for 0 dBu Output3D MIX PROª Block Digram 3D Mix Proª Hookup Diagram Important Safety Instructions P a „ O L Secci-n Maestra Master Salidas Principales Main Outputs Poder Y TierraSalidas DE Monitor CONTROLES/INDICADORES EntradasLED cue/cue Switch Indicador de Mute SilencioFader de Canal Entradas Mic 1/MicNivel Principal LED de PoderPaneo Principal Der.-Izq Nivel de CabinaSelecci-n de Aud’fonos Salida de Aud’fonosFader-X Efectos Controles DE Loops DE EfectosExpansor Espacial SRS Especificaciones DE LA 3D MIX PRO Instrucciones DE Seguridad Importantes Deux canaux stŽrŽos indŽpendants Deux entrŽes stŽrŽos Deux entrŽes microContrles micros Section Master Alimentation ET Mise Ë LA MassePrise dÕalimentation IEC Interrupteur dÕalimentationSorties Monitor Sorties PrincipalesCanaux Dõentree 1 ET SEND/RETURN EffetsEntrees CONTROLES/INDICATEURSSection Master Entrees ET Controles DES Micros33. SŽlecteur de mode Žcouteurs Niveau BoothMain Pan Droite/Gauche Niveau MonoEffets Expandeur SpatialCrossfader Contrle Space SRS Conservez CES Instructions Eigenschaften Zwei Stereo KanŠle Eigenschaften pro KanalZwei MikrofoneingŠnge Eigenschaften pro Eingang FŸr beide EingŠnge gemeinsam 2 Band EQ Strom UND ErdungMaster Sektion KaltgerŠteanschlu§Hz Rumble Schalter Booth Outputs L und RMain Stereo Outputs L und R, symetrisch Main Chinch Outputs L und R, asymetrischInput KAN€LE 1 UND Signal LEDDIE Anzeigen UND Regler 11. CD/Line InputMic Signal Level / LED MIC Input UND RegelungMute Schalter / LED Stereo Output Level Meter Effects Loop Effekte3D MIX PRO Specifications Wichtige Sicherheitsrichtlinien Page Page Page Peavey Electronics Corporation Limited Warranty 80304491