Peavey 3D Mix Pro manual Back Panel Power and Grounding, Main Outputs

Page 5

BACK PANEL

3

2

1

POWER AND GROUNDING

1. Removable AC Power Cord/IEC Socket

This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used. (See voltage marking on unit.) Never remove or cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord. When lost or damaged, replace this cord with

one of the proper ratings.

2. Power Switch

This switch applies power to the unit. Press the switch to the (I) position to turn the unit on. Return the switch to the (O) position to turn it off. The Power LED (24) will illuminate when proper power is supplied to the 3D Mix Pro.

3. Phono Ground

Grounds from external turntables should be connected at this point. Note: There are two points on the rear of the unit for convenience.

MAIN OUTPUTS

			5
			6
10	9	4	7	8

4. Mono Out

This 1/4" output supplies an unbalanced mono (L+R) signal to an outboard EQ, power amp, lighting system, or subwoofer crossover etc. The Mono Out level is set by the Mono Level control (29).

5

Image 5

Contents 3D Mix Pro Page Two Microphone Inputs Features per input Two Distinct Stereo Input Channels Features per channelMaster Section Master mic featuresMain Outputs Back Panel Power and GroundingEffects SEND/RETURN Monitor OutputsInput Channels 1 InputsCONTROLS/INDICATORS Master Section MIC Inputs and ControlsStereo Output Level Indicator Booth LevelMono Level Headphone Cue LevelSpatial Expander EffectsEffects Loop Controls HUM and Noise 22 Hz 22 kHz BW 3D MIX PRO SpecificationsStereo Channel EQ +12 dB, -22dB MIN Input Levels for 0 dBu Output3D MIX PROª Block Digram 3D Mix Proª Hookup Diagram Important Safety Instructions P a „ O L Secci-n Maestra Master Salidas Principales Main Outputs Poder Y TierraSalidas DE Monitor CONTROLES/INDICADORES EntradasLED cue/cue Switch Indicador de Mute SilencioFader de Canal Entradas Mic 1/MicNivel Principal LED de PoderPaneo Principal Der.-Izq Nivel de CabinaFader-X Selecci-n de Aud’fonosSalida de Aud’fonos Expansor Espacial SRS EfectosControles DE Loops DE Efectos Especificaciones DE LA 3D MIX PRO Instrucciones DE Seguridad Importantes Contrles micros Deux canaux stŽrŽos indŽpendants Deux entrŽes stŽrŽosDeux entrŽes micro Section Master Alimentation ET Mise Ë LA MassePrise dÕalimentation IEC Interrupteur dÕalimentationSorties Monitor Sorties PrincipalesCanaux Dõentree 1 ET SEND/RETURN EffetsEntrees CONTROLES/INDICATEURSSection Master Entrees ET Controles DES Micros33. SŽlecteur de mode Žcouteurs Niveau BoothMain Pan Droite/Gauche Niveau MonoCrossfader EffetsExpandeur Spatial Contrle Space SRS Conservez CES Instructions Zwei MikrofoneingŠnge Eigenschaften pro Eingang EigenschaftenZwei Stereo KanŠle Eigenschaften pro Kanal FŸr beide EingŠnge gemeinsam 2 Band EQ Strom UND ErdungMaster Sektion KaltgerŠteanschlu§Hz Rumble Schalter Booth Outputs L und RMain Stereo Outputs L und R, symetrisch Main Chinch Outputs L und R, asymetrischInput KAN€LE 1 UND Signal LEDDIE Anzeigen UND Regler 11. CD/Line InputMute Schalter / LED Mic Signal Level / LEDMIC Input UND Regelung Stereo Output Level Meter Effects Loop Effekte3D MIX PRO Specifications Wichtige Sicherheitsrichtlinien Page Page Page Peavey Electronics Corporation Limited Warranty 80304491