Fostex manual Usage examples of LR16, Integrating the main unit and control unit

Page 14

Model LR16 [Before using the unit]

Usage examples of LR16

The control unit and main unit of the LR16 are separated. You can set these units flexibly.

<Usage example 1>

Integrating the main unit and control unit.

You can integrate the main unit and con- trol unit.

Use the supplied CAT-5 cable (approx. 50 cm length) to connect between the units. See the next page for details about how to integrate the units.

<Usage example 2>

Mounting the main unit and control unit on the rack.

As shown on the right, you can mount each unit to the rack. In this case, use a CAT-5 cable which has enough length for connecting between the units (the cable supplied with the LR16 is approxi- mately 50 cm length).

<Note>: Use only a CAT-5 STP cable for connection between the main unit and the control unit.

<Usage example 3>

Setting the main unit and control unit separately.

You can set the main unit and control unit over a 50 meter distance. In such a case, use a CAT-5 cable which has enough length for connecting between the units (the cable sup- plied with the LR16 is approximately 50 cm length).

<Note>: Use only a CAT-5 STP cable for connection between the main unit and the control unit.

14

Image 14

Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Signal flow of the mixer Connecting sources Adjusting the input level Low-cut filter Limiter EqualizerRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation Condensation About version upgradeCleaning the exterior About copyrightsMain features OverviewRecorder section main unit features Before using the unit Unpacking the cartonIntegrating the main unit and control unit Setting the main unit and control unit separatelyUsage examples of LR16 Mounting the main unit and control unit on the rackIntegrating the control unit and main unit Necessary itemsRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection to external devices Connection example live recordingConnection example home recording MTRBalanced and unbalanced inputs/outputs BalancedNames and functions Control unit input channel 1 through 14 ST/1-2/3-4 assign switches POST/PRE switchMute switch Solo switchMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section Assign to Stereo OUT switches AUX Send controls / Solo switches24 27 EFF Send control / Solo switch Output Limiter switchControl unit rear panel Main unit front panelST MIX key NEW Project keyTransport keys REC Track Select 1-16 keysMain unit rear panel Home screen Display detailsMenu mode screen Memory play setup mode screenModel LR16 Names and functions Mixer functions Signal flow of the mixer Mixer basicsConnecting sources to the input connectors Connecting sourcesAdjusting the input level Phantom power supply settingLow-cut filter Gain adjustment while monitoringEqualizer LimiterPre-fader Using an external effect processorUsing AUX 1, 2 Post-faderApplying the internal effects Using the internal effects processorUsing Insert Monitoring About the effect typesChannel grouping Solo monitorUsing SUB Set the Source switches on channels 15 and 16 to TRKBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Recording mode ProjectLive recording BassRecording to tracks 1 through Adjusting input level =recording level of each mixer channel PreparationAdjusting the channel output levels sent to the stereo buss RecordingPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Overdubbing Connecting a sound sourceAdjusting the input level while playing back tracks 1 Multitrack recordingMixdown Performing overdubAdjusting level and sound of each track Starting mixdown recordingPunch in/out using the transport control keys Punch in/outPunch in/out using a footswitch At the punch out point, press only the Play keyModel LR16 Recorder functions / Recording/playback Memory play Section of the main unit Memory Setup key in the recorderPress the Enter key Numeric key number 0 through 9Selecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Performing memory play Press an illuminated numeric keyAdding a mark on-the-fly Mark functionAdding a mark Adding a mark via the mark list screenEditing a mark label Locating to a mark pointEditing a mark Press the Enter key to bring up the Menu screenExample of label editing Editing a mark positionDeleting a mark Edit the time data in the following mannerCreating a new project Project managementSelecting a project While Select is highlighted, pressEditing a project name Use the Menu dial to highlight Rename press the Enter keyRight Rolling back a projectName editing example Use the 3 key to enter aSaving a project to an external medium Use the Menu dial to highlight Roll back press the Enter keySelecting tracks Export screen detailsEditing the duration Use the Menu dial to highlight Export press the Enter keyCopying a stereo mix file to an external medium Press any operation keySelect the files to be exported Selecting a desired fileSelecting all files Protecting a project Deleting a projectDisplay now shows the project list screen Enabling USB connection Use the Menu dial to highlight USB and press the Enter keyWhile ? is flashing on the screen, press the Enter key Protecting the internal hard diskWhile USB to PC is highlighted, press the Enter key LR16 ECopying data from the LR16 to a computer Other functions Adjusting the display contrastSetting the footswtich function Press the Enter key to bring upInitializing the system memory Setting items DefaultFormatting the internal hard disk While holding down the Record key, press the Enter keyTo assign the destination channels of SUB Use the Menu dial to highlight Input and press the Enter keySoftware version upgrade MethodTurn on the LR16 Press the Enter key to bring up Menu screen Midi message supported by the LR16 Setting frame rateMidi synchronization Midi connectionSetting FS/Bit of project While Default FS menu is highlighted, press the Enter keyInput and Output Controller unit SpecificationsInput and Output Main unit Inputs/OutputsGeneral Physical dimensionsPower Consumption approx W Main unitMidi Implementation Chart Model LR16Declaration of EC Directive Affect of Immunity on This EquipmentForthe US Customers only Fostex America Limited Warranty Shipping Index 45, 52Page Fostex CO