Fostex LR16 manual Connecting the power cord, Turning on the power, Preparation of power supply

Page 17

Model LR16 [Before using the unit]

Preparation of power supply

Connecting the power cord

Using the supplied power cord, con- nect the [AC IN] connector on the rear panel of the main unit and the AC outlet.

<Note>: Use only the supplied power cord.

[POWER] switch

AC outlet

Turning on the power

Press down the [POWER] switch on the rear panel of the main unit to turn on the power.

After a while, the LR16 normally starts up and the display on the recorder unit shows "<No project>" (indicating that nothing is recorded on the recorder's hard disk).

For details about recording, see "Mixer function" on page 33 and "Recorder function" on page 43.

To turn on or off the LR16 and peripheral devices which are connected to the LR16, follow the proper procedures described below.

Procedures of turning on the power after connecting peripheral devices

<Note>: Before turning on or off the LR16 and peripheral devices which are connected to the LR16, make sure that the channel faders and monitor gain control of the LR16, as well as the volume control of an monitor amplifier (or powered monitor speaker), are set to minimum. Otherwise, a loud sound may be produced suddenly that may damage the speaker or your hearing.

(1)Turn on the devices connected to the [INPUT] connectors to the LR16.

(2)Turn on the LR16.

(3)Turn on the monitor amplifier (or powered monitor speaker).

Procedures of turning off the power after connecting peripheral devices

(1)Turn off the monitor amplifier (or powered monitor speaker).

(2)Turn off the LR16.

(3)Turn off the devices connected to the [INPUT] connectors to the LR16.

17

Image 17
Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation Cleaning the exterior About version upgradeCondensation About copyrightsOverview Main featuresRecorder section main unit features Unpacking the carton Before using the unitUsage examples of LR16 Setting the main unit and control unit separatelyIntegrating the main unit and control unit Mounting the main unit and control unit on the rackNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection example live recording Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Mute switch POST/PRE switch14 ST/1-2/3-4 assign switches Solo switchMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section 24 27 EFF Send control / Solo switch AUX Send controls / Solo switchesAssign to Stereo OUT switches Output Limiter switchMain unit front panel Control unit rear panelTransport keys NEW Project keyST MIX key REC Track Select 1-16 keysMain unit rear panel Display details Home screenMemory play setup mode screen Menu mode screenModel LR16 Names and functions Mixer functions Mixer basics Signal flow of the mixerAdjusting the input level Connecting sourcesConnecting sources to the input connectors Phantom power supply settingEqualizer Gain adjustment while monitoringLow-cut filter LimiterUsing AUX 1, 2 Using an external effect processorPre-fader Post-faderApplying the internal effects Using the internal effects processorUsing Insert About the effect types MonitoringSolo monitor Channel groupingSet the Source switches on channels 15 and 16 to TRK Using SUBBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Project Recording modeBass Live recordingRecording to tracks 1 through Preparation Adjusting input level =recording level of each mixer channelRecording Adjusting the channel output levels sent to the stereo bussPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Adjusting the input level while playing back tracks 1 Connecting a sound sourceOverdubbing Multitrack recordingPerforming overdub MixdownStarting mixdown recording Adjusting level and sound of each trackPunch in/out Punch in/out using the transport control keysAt the punch out point, press only the Play key Punch in/out using a footswitchModel LR16 Recorder functions / Recording/playback Memory play Press the Enter key Memory Setup key in the recorderSection of the main unit Numeric key number 0 through 9Selecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Press an illuminated numeric key Performing memory playAdding a mark Mark functionAdding a mark on-the-fly Adding a mark via the mark list screenEditing a mark Locating to a mark pointEditing a mark label Press the Enter key to bring up the Menu screenEditing a mark position Example of label editingEdit the time data in the following manner Deleting a markSelecting a project Project managementCreating a new project While Select is highlighted, pressUse the Menu dial to highlight Rename press the Enter key Editing a project nameName editing example Rolling back a projectRight Use the 3 key to enter aUse the Menu dial to highlight Roll back press the Enter key Saving a project to an external mediumEditing the duration Export screen detailsSelecting tracks Use the Menu dial to highlight Export press the Enter keyPress any operation key Copying a stereo mix file to an external mediumSelect the files to be exported Selecting a desired fileSelecting all files Deleting a project Protecting a projectDisplay now shows the project list screen Use the Menu dial to highlight USB and press the Enter key Enabling USB connectionWhile USB to PC is highlighted, press the Enter key Protecting the internal hard diskWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Setting the footswtich function Adjusting the display contrastOther functions Press the Enter key to bring upFormatting the internal hard disk Setting items DefaultInitializing the system memory While holding down the Record key, press the Enter keyUse the Menu dial to highlight Input and press the Enter key To assign the destination channels of SUBMethod Software version upgradeTurn on the LR16 Press the Enter key to bring up Menu screen Midi synchronization Setting frame rateMidi message supported by the LR16 Midi connectionWhile Default FS menu is highlighted, press the Enter key Setting FS/Bit of projectInput and Output Main unit SpecificationsInput and Output Controller unit Inputs/OutputsPower Consumption approx W Physical dimensionsGeneral Main unitModel LR16 Midi Implementation ChartAffect of Immunity on This Equipment Declaration of EC DirectiveForthe US Customers only Fostex America Limited Warranty Shipping 45, 52 IndexPage Fostex CO