Fostex LR16 manual Adjusting level and sound of each track, Starting mixdown recording

Page 53

Model LR16 [Recorder functions / Recording/playback]

Preparation

(1)Set the [SOURCE] switch on each of mixer channels 1 through 16 to "TRK" ().

The corresponding recorder track output is selected as the channel source of each channel.

(2)Turn off the [NEW PROJECT] key in the recorder section.

(3)Change the destination channels of Sub In from “15/16” (default) to “-/-” (no channels are assigned).

See page 79 for details about how to assign the destination channels of Sub In.

Adjusting level and sound of each track

(1)Set the [ST] switch on each of mixer channels 1 through 16 to ON ().

Each input signal is routed to the stereo L/R buss via the input fader.

(2)Raise the [STEREO] fader to the "0" position.

(3)Press the [PLAY] key in the recorder or mixer section to start playback of the project.

(4)Use the channel fader on each mixer channel to adjust the track level.

The display shows the levels of tracks 1 through 16 as well as the stereo L/R buss.

You can also control each track sound us- ing the equalizer on each channel and the internal effects processor, as well as set pan. For details about the mixer function, see "Mixer function" on page 33.

(5)Use the [STEREO] fader to adjust the total level of the stereo L/R buss.

You can monitor the stereo L/R buss by raising the [PHONES] and [MONITOR] controls.

(6)After finishing adjustment, press the [STOP] key in the recorder or mixer section to stop the recorder.

If you press the [STOP] key in the recorder section, the recorder stops at the recording end position (REC END).

If you press the [STOP] key in the mixer section, the recorder skips back to the beginning of the project (ABS 0) and stops.

Starting mixdown recording

(1)Press the [ST MIX] key in the recorder section to turn it on.

"LR" starts flashing on the display and the recordable remaining time is shown.

(2)Press the [PLAY] key while holding down the [RECORD] key to start mixdown recording.

<Note>: Do not press the [NEW PRJ. REC] key in the mixer section.

(3)After finishing mixdown recording, press the [STOP] key in the recorder or mixer section to stop the recorder.

If you press the [STOP] key in the recorder section, the recorder stops at the recording end position (REC END).

If you press the [STOP] key in the mixer section, the recorder skips back to the beginning of the project (ABS 0) and stops.

<Memo>: The mixed down file (stereo WAV file) is stored to the "2mix" folder in the current project.

take001trk01 take001trk02 take001trk03

PROJ001

take001trk04take001trk16

2mixPROJ001-01

You can copy the mixed down file to a per- sonal computer by directly connecting the com- puter to the LR16 or via a USB memory stick. (See page 73 for details about how to transfer to a computer. See page 67 for details about how to copy to a USB memory stick.)

<Note>: You cannot play back a mixed down file directly, however, you can play it back using the memory play function (see page 57).

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation Cleaning the exterior About version upgradeCondensation About copyrightsOverview Main featuresRecorder section main unit features Unpacking the carton Before using the unitUsage examples of LR16 Setting the main unit and control unit separatelyIntegrating the main unit and control unit Mounting the main unit and control unit on the rackNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection example live recording Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Mute switch POST/PRE switch14 ST/1-2/3-4 assign switches Solo switchMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section 24 27 EFF Send control / Solo switch AUX Send controls / Solo switchesAssign to Stereo OUT switches Output Limiter switchMain unit front panel Control unit rear panelTransport keys NEW Project keyST MIX key REC Track Select 1-16 keysMain unit rear panel Display details Home screenMemory play setup mode screen Menu mode screenModel LR16 Names and functions Mixer functions Mixer basics Signal flow of the mixerAdjusting the input level Connecting sourcesConnecting sources to the input connectors Phantom power supply settingEqualizer Gain adjustment while monitoringLow-cut filter LimiterUsing AUX 1, 2 Using an external effect processorPre-fader Post-faderApplying the internal effects Using the internal effects processorUsing Insert About the effect types MonitoringSolo monitor Channel groupingSet the Source switches on channels 15 and 16 to TRK Using SUBBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Project Recording modeBass Live recordingRecording to tracks 1 through Preparation Adjusting input level =recording level of each mixer channelRecording Adjusting the channel output levels sent to the stereo bussPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Adjusting the input level while playing back tracks 1 Connecting a sound sourceOverdubbing Multitrack recordingPerforming overdub MixdownStarting mixdown recording Adjusting level and sound of each trackPunch in/out Punch in/out using the transport control keysAt the punch out point, press only the Play key Punch in/out using a footswitchModel LR16 Recorder functions / Recording/playback Memory play Press the Enter key Memory Setup key in the recorderSection of the main unit Numeric key number 0 through 9Selecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Press an illuminated numeric key Performing memory playAdding a mark Mark functionAdding a mark on-the-fly Adding a mark via the mark list screenEditing a mark Locating to a mark pointEditing a mark label Press the Enter key to bring up the Menu screenEditing a mark position Example of label editingEdit the time data in the following manner Deleting a markSelecting a project Project managementCreating a new project While Select is highlighted, pressUse the Menu dial to highlight Rename press the Enter key Editing a project nameName editing example Rolling back a projectRight Use the 3 key to enter aUse the Menu dial to highlight Roll back press the Enter key Saving a project to an external mediumEditing the duration Export screen detailsSelecting tracks Use the Menu dial to highlight Export press the Enter keyPress any operation key Copying a stereo mix file to an external mediumSelect the files to be exported Selecting a desired fileSelecting all files Deleting a project Protecting a projectDisplay now shows the project list screen Use the Menu dial to highlight USB and press the Enter key Enabling USB connectionWhile USB to PC is highlighted, press the Enter key Protecting the internal hard diskWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Setting the footswtich function Adjusting the display contrastOther functions Press the Enter key to bring upFormatting the internal hard disk Setting items DefaultInitializing the system memory While holding down the Record key, press the Enter keyUse the Menu dial to highlight Input and press the Enter key To assign the destination channels of SUBMethod Software version upgradeTurn on the LR16 Press the Enter key to bring up Menu screen Midi synchronization Setting frame rateMidi message supported by the LR16 Midi connectionWhile Default FS menu is highlighted, press the Enter key Setting FS/Bit of projectInput and Output Main unit SpecificationsInput and Output Controller unit Inputs/OutputsPower Consumption approx W Physical dimensionsGeneral Main unitModel LR16 Midi Implementation ChartAffect of Immunity on This Equipment Declaration of EC DirectiveForthe US Customers only Fostex America Limited Warranty Shipping 45, 52 IndexPage Fostex CO
Top Page Image Contents