Fostex LR16 manual Export screen details, Editing the duration, Selecting tracks

Page 69

Model LR16 [Recorder functions / Project management]

(3)Use the [MENU] dial to highlight "Export" press the [ENTER] key.

After the LR16 checks the USB memory, the display shows the export screen.

For details about the information shown on this screen, see "Export screen details" de- scribed below.

If you simply execute step (4) on the next page without changing any parameter, data of full length (from ABS 0 to REC END) of all tracks (1 through 16) is exported to the USB memory stick.

Before you execute step (4), however, you can shorten the length of the project or se- lect tracks to be exported (see the right col- umn on this page for details).

<Export screen details>

1

2

3

4

5

Duration of the project to be exported. By de-

1fault, the full length (from ABS 0 to REC END) is shown.You can edit and shorten it.

2The start track to be exported (by default, 01). You can change it.

The end track to be exported (by default, 16).

3You can change it. The value in parentheses shows the required space for storing.

4The volume label of the USB memory stick. The free area of the USB memory stick.

<Note>: If you attempt to export the

5project data which exceeds the free area of the USB memory stick, "Over size!" is shown and you cannot execute ex- porting data.

<Editing the duration>

1)While "Duration" is highlighted, press the [ENTER] key.

The second digit starts flashing.

2)Use the [MENU] dial or numeric keys to enter the desired value at the flashing point, and press the [ENTER] key.

You can use the [REWIND] or [F FWD] key to move the cursor (flashing point).

<Note>: Pressing the [CLEAR] key resets the duration to "00H 00M 00S". If you shorten the duration, the value in parentheses shown at the right of the "End TR" number gets smaller.

<Selecting tracks>

1)Use the [MENU] dial to highlight "Start TR" (or "End TR") and press the [ENTER] key.

The track number of the starting track (or ending track) starts flashing.

2)Use the [MENU] dial to enter the desired track number and press the [ENTER] key to confirm the setting.

<Note>: If you limit the tracks, the value in parentheses shown at the right of the "End TR" number gets smaller.

69

Image 69

Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesRecorder functions Recording/Playback Setting on the memory play setup screen Performing memory playAdding a mark Adding a mark on-the-fly Specifications Recorder functions File transfer to/from a computerRecorder functions Other functions About power supply Precautions on installationIntroduction Cleaning the exterior About version upgradeCondensation About copyrightsOverview Main featuresRecorder section main unit features Unpacking the carton Before using the unitUsage examples of LR16 Setting the main unit and control unit separatelyIntegrating the main unit and control unit Mounting the main unit and control unit on the rackNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Connecting the power cord Turning on the powerPreparation of power supply Connection example live recording Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Mute switch POST/PRE switch14 ST/1-2/3-4 assign switches Solo switchControl unit Master channel SUB in jacks and controlMonitor section Phantom 1-8, 9-16 indicators Internal effects sectionRecorder control section 24 27 EFF Send control / Solo switch AUX Send controls / Solo switchesAssign to Stereo OUT switches Output Limiter switchMain unit front panel Control unit rear panelTransport keys NEW Project keyST MIX key REC Track Select 1-16 keysMain unit rear panel Display details Home screenMemory play setup mode screen Menu mode screenModel LR16 Names and functions Mixer functions Mixer basics Signal flow of the mixerAdjusting the input level Connecting sourcesConnecting sources to the input connectors Phantom power supply settingEqualizer Gain adjustment while monitoringLow-cut filter LimiterUsing AUX 1, 2 Using an external effect processorPre-fader Post-faderUsing the internal effects processor Using InsertApplying the internal effects About the effect types MonitoringSolo monitor Channel groupingSet the Source switches on channels 15 and 16 to TRK Using SUBBlock diagram Recorder functions Recording/playback Recording formatRecorder basics Project Recording modeBass Live recordingRecording to tracks 1 through Preparation Adjusting input level =recording level of each mixer channelRecording Adjusting the channel output levels sent to the stereo bussPlaying back a project Locate to the beginning of the projectPress the Play key in the recorder or mixer section Adjusting the input level while playing back tracks 1 Connecting a sound sourceOverdubbing Multitrack recordingPerforming overdub MixdownStarting mixdown recording Adjusting level and sound of each trackPunch in/out Punch in/out using the transport control keysAt the punch out point, press only the Play key Punch in/out using a footswitchModel LR16 Recorder functions / Recording/playback Memory play Press the Enter key Memory Setup key in the recorderSection of the main unit Numeric key number 0 through 9Selecting the memory play mode After you complete assignment,press EXIT/NO keySelecting a channel pair for memory play Press an illuminated numeric key Performing memory playAdding a mark Mark functionAdding a mark on-the-fly Adding a mark via the mark list screenEditing a mark Locating to a mark pointEditing a mark label Press the Enter key to bring up the Menu screenEditing a mark position Example of label editingEdit the time data in the following manner Deleting a markSelecting a project Project managementCreating a new project While Select is highlighted, pressUse the Menu dial to highlight Rename press the Enter key Editing a project nameName editing example Rolling back a projectRight Use the 3 key to enter aUse the Menu dial to highlight Roll back press the Enter key Saving a project to an external mediumEditing the duration Export screen detailsSelecting tracks Use the Menu dial to highlight Export press the Enter keyPress any operation key Copying a stereo mix file to an external mediumSelecting a desired file Selecting all filesSelect the files to be exported Deleting a project Protecting a projectDisplay now shows the project list screen Use the Menu dial to highlight USB and press the Enter key Enabling USB connectionWhile USB to PC is highlighted, press the Enter key Protecting the internal hard diskWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Setting the footswtich function Adjusting the display contrastOther functions Press the Enter key to bring upFormatting the internal hard disk Setting items DefaultInitializing the system memory While holding down the Record key, press the Enter keyUse the Menu dial to highlight Input and press the Enter key To assign the destination channels of SUBMethod Software version upgradeTurn on the LR16 Press the Enter key to bring up Menu screen Midi synchronization Setting frame rateMidi message supported by the LR16 Midi connectionWhile Default FS menu is highlighted, press the Enter key Setting FS/Bit of projectInput and Output Main unit SpecificationsInput and Output Controller unit Inputs/OutputsPower Consumption approx W Physical dimensionsGeneral Main unitModel LR16 Midi Implementation ChartAffect of Immunity on This Equipment Declaration of EC DirectiveForthe US Customers only Fostex America Limited Warranty Shipping 45, 52 IndexPage Fostex CO