Fostex LR16 manual Selecting a desired file, Selecting all files, Select the files to be exported

Page 71

Model LR16 [Recorder functions / Project management]

(3)Use the [MENU] dial to highlight "Export ST mix" press the [ENTER] key.

After the LR16 checks the USB memory, the display shows the "export 2 mix" screen.

On this screen, stereo mix files in the

"2 mix" folder of the current project are listed up.

In the screen example above, two stereo mix files exists.

(4)Select the file(s) to be exported.

You can export any desired file(s) or all files.

<Selecting a desired file>

By using the [MENU] dial to select a desired file and pressing the [ENTER] key, you can put a checkmark to the left of the file name, while the volume of the selected file is shown on the right of "-File select-".

By repeating the operation above, you can put a checkmark to another file.

<Selecting all files>

By pressing the [ENTER] key while

"[All select]" is highlighted, a checkmark is put to every file as below.

<Memo>: To deselect a file, highlight a desired file with a checkmark and press the [ENTER] key. The checkmark is re- moved.

(5)Use the [MENU] dial to highlight "[EXECUTE]" at the bottom and press the [ENTER] key.

<Note>: If the data of a project with the same name exists on the USB memory stick when you attempt to execute ex- porting the project data by pressing the [ENTER] key, the following popup ap- pears.

To overwrite the existing data, press the [ENTER] key. If you do not want to over- write the existing data, press the [EXIT/ NO] key to cancel exporting data.

The LR16 starts exporting data to the USB memory stick and the display shows the progress. The display also shows the ap- proximate finish time and remain size of the USB memory stick.

71

Image 71

Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation About copyrights About version upgradeCleaning the exterior CondensationOverview Main featuresRecorder section main unit features Unpacking the carton Before using the unitMounting the main unit and control unit on the rack Setting the main unit and control unit separatelyUsage examples of LR16 Integrating the main unit and control unitNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection example live recording Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Solo switch POST/PRE switchMute switch 14 ST/1-2/3-4 assign switchesMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section Output Limiter switch AUX Send controls / Solo switches24 27 EFF Send control / Solo switch Assign to Stereo OUT switchesMain unit front panel Control unit rear panelREC Track Select 1-16 keys NEW Project keyTransport keys ST MIX keyMain unit rear panel Display details Home screenMemory play setup mode screen Menu mode screenModel LR16 Names and functions Mixer functions Mixer basics Signal flow of the mixerPhantom power supply setting Connecting sourcesAdjusting the input level Connecting sources to the input connectorsLimiter Gain adjustment while monitoringEqualizer Low-cut filterPost-fader Using an external effect processorUsing AUX 1, 2 Pre-faderApplying the internal effects Using the internal effects processorUsing Insert About the effect types MonitoringSolo monitor Channel groupingSet the Source switches on channels 15 and 16 to TRK Using SUBBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Project Recording modeBass Live recordingRecording to tracks 1 through Preparation Adjusting input level =recording level of each mixer channelRecording Adjusting the channel output levels sent to the stereo bussPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Multitrack recording Connecting a sound sourceAdjusting the input level while playing back tracks 1 OverdubbingPerforming overdub MixdownStarting mixdown recording Adjusting level and sound of each trackPunch in/out Punch in/out using the transport control keysAt the punch out point, press only the Play key Punch in/out using a footswitchModel LR16 Recorder functions / Recording/playback Memory play Numeric key number 0 through 9 Memory Setup key in the recorderPress the Enter key Section of the main unitSelecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Press an illuminated numeric key Performing memory playAdding a mark via the mark list screen Mark functionAdding a mark Adding a mark on-the-flyPress the Enter key to bring up the Menu screen Locating to a mark pointEditing a mark Editing a mark labelEditing a mark position Example of label editingEdit the time data in the following manner Deleting a markWhile Select is highlighted, press Project managementSelecting a project Creating a new projectUse the Menu dial to highlight Rename press the Enter key Editing a project nameUse the 3 key to enter a Rolling back a projectName editing example RightUse the Menu dial to highlight Roll back press the Enter key Saving a project to an external mediumUse the Menu dial to highlight Export press the Enter key Export screen detailsEditing the duration Selecting tracksPress any operation key Copying a stereo mix file to an external mediumSelect the files to be exported Selecting a desired fileSelecting all files Deleting a project Protecting a projectDisplay now shows the project list screen Use the Menu dial to highlight USB and press the Enter key Enabling USB connectionLR16 E Protecting the internal hard diskWhile USB to PC is highlighted, press the Enter key While ? is flashing on the screen, press the Enter keyCopying data from the LR16 to a computer Press the Enter key to bring up Adjusting the display contrastSetting the footswtich function Other functionsWhile holding down the Record key, press the Enter key Setting items DefaultFormatting the internal hard disk Initializing the system memoryUse the Menu dial to highlight Input and press the Enter key To assign the destination channels of SUBMethod Software version upgradeTurn on the LR16 Press the Enter key to bring up Menu screen Midi connection Setting frame rateMidi synchronization Midi message supported by the LR16While Default FS menu is highlighted, press the Enter key Setting FS/Bit of projectInputs/Outputs SpecificationsInput and Output Main unit Input and Output Controller unitMain unit Physical dimensionsPower Consumption approx W GeneralModel LR16 Midi Implementation ChartAffect of Immunity on This Equipment Declaration of EC DirectiveForthe US Customers only Fostex America Limited Warranty Shipping 45, 52 IndexPage Fostex CO