Fostex LR16 Other functions, Adjusting the display contrast, Setting the footswtich function

Page 77

Model LR16 [Recorder function / Other functions]

Other functions

Adjusting the display contrast

If the display is difficult to see, you can adjust the display contrast by rotating the [MENU] dial while the LR16 is turned on.

Rotating the [MENU] dial counterclockwise increases the contrast. Rotating the [MENU] dial clockwise decreases the contrast.

(3) Use the [MENU] dial to highlight "Foot SW" and press the [ENTER] key.

The current setting starts flashing and you can now change the setting (by default, "P I/O" flashes).

<Memo>: The contrast setting remains in effect even if you turn off the LR16. If you initialize the system memory via the "Sys default memory" menu item of the "System" menu, the contrast reverts back

to the default setting.

You can select from the following options.

Setting the footswtich function

You can select the function of a footswitch connected to the [FOOT SW] jack on the rear panel of the main unit between the punch in/out function and memory play start/stop function.

(1)Press the [ENTER] key to bring up the

	P I/O	A connected footswitch acts as the
		punch in/out switch.


	MEM 0 A connected footswitch acts the same

Ias the associated memory key.Press-

Iing the footswitch starts or stop

MEM 9 memory play.

(4)Use the [MENU] dial to highlight the desired option and press the [ENTER] key to confirm the setting.

MENU screen.	(5) Press the [STOP] key to exit the MENU
When you bring up the MENU screen for	mode.
the first time, "Mark point" is highlighted.

(2)Use the [MENU] dial to highlight "System" and press the [ENTER] key.

The display now shows the system menu screen.

<Memo>: If you initialize the system memory via the "Sys default memory" menu item of the "System" menu, the footswitch function reverts back to the default setting (P I/O).

77

Image 77

Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation Cleaning the exterior About version upgradeCondensation About copyrightsOverview Main featuresRecorder section main unit features Unpacking the carton Before using the unitUsage examples of LR16 Setting the main unit and control unit separatelyIntegrating the main unit and control unit Mounting the main unit and control unit on the rackNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection example live recording Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Mute switch POST/PRE switch14 ST/1-2/3-4 assign switches Solo switchMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section 24 27 EFF Send control / Solo switch AUX Send controls / Solo switchesAssign to Stereo OUT switches Output Limiter switchMain unit front panel Control unit rear panelTransport keys NEW Project keyST MIX key REC Track Select 1-16 keysMain unit rear panel Display details Home screenMemory play setup mode screen Menu mode screenModel LR16 Names and functions Mixer functions Mixer basics Signal flow of the mixerAdjusting the input level Connecting sourcesConnecting sources to the input connectors Phantom power supply settingEqualizer Gain adjustment while monitoringLow-cut filter LimiterUsing AUX 1, 2 Using an external effect processorPre-fader Post-faderApplying the internal effects Using the internal effects processorUsing Insert About the effect types MonitoringSolo monitor Channel groupingSet the Source switches on channels 15 and 16 to TRK Using SUBBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Project Recording modeBass Live recordingRecording to tracks 1 through Preparation Adjusting input level =recording level of each mixer channelRecording Adjusting the channel output levels sent to the stereo bussPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Adjusting the input level while playing back tracks 1 Connecting a sound sourceOverdubbing Multitrack recordingPerforming overdub MixdownStarting mixdown recording Adjusting level and sound of each trackPunch in/out Punch in/out using the transport control keysAt the punch out point, press only the Play key Punch in/out using a footswitchModel LR16 Recorder functions / Recording/playback Memory play Press the Enter key Memory Setup key in the recorderSection of the main unit Numeric key number 0 through 9Selecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Press an illuminated numeric key Performing memory playAdding a mark Mark functionAdding a mark on-the-fly Adding a mark via the mark list screenEditing a mark Locating to a mark pointEditing a mark label Press the Enter key to bring up the Menu screenEditing a mark position Example of label editingEdit the time data in the following manner Deleting a markSelecting a project Project managementCreating a new project While Select is highlighted, pressUse the Menu dial to highlight Rename press the Enter key Editing a project nameName editing example Rolling back a projectRight Use the 3 key to enter aUse the Menu dial to highlight Roll back press the Enter key Saving a project to an external mediumEditing the duration Export screen detailsSelecting tracks Use the Menu dial to highlight Export press the Enter keyPress any operation key Copying a stereo mix file to an external mediumSelect the files to be exported Selecting a desired fileSelecting all files Deleting a project Protecting a projectDisplay now shows the project list screen Use the Menu dial to highlight USB and press the Enter key Enabling USB connectionWhile USB to PC is highlighted, press the Enter key Protecting the internal hard diskWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Setting the footswtich function Adjusting the display contrastOther functions Press the Enter key to bring upFormatting the internal hard disk Setting items DefaultInitializing the system memory While holding down the Record key, press the Enter keyUse the Menu dial to highlight Input and press the Enter key To assign the destination channels of SUBMethod Software version upgradeTurn on the LR16 Press the Enter key to bring up Menu screen Midi synchronization Setting frame rateMidi message supported by the LR16 Midi connectionWhile Default FS menu is highlighted, press the Enter key Setting FS/Bit of projectInput and Output Main unit SpecificationsInput and Output Controller unit Inputs/OutputsPower Consumption approx W Physical dimensionsGeneral Main unitModel LR16 Midi Implementation ChartAffect of Immunity on This Equipment Declaration of EC DirectiveForthe US Customers only Fostex America Limited Warranty Shipping 45, 52 IndexPage Fostex CO