Fostex LR16 manual Balanced and unbalanced inputs/outputs

Page 20

Model LR16 [Connection to external devices]

Balanced and unbalanced inputs/outputs

For connection between a recording mixer such as the LR16 and external devices (such as a microphone, keyboard, recorder, etc), shielded cables are used. There are two types of cables - balanced and unbalanced.

Cold

Hot

Shield (ground)

Outer jacket

Balanced

Unbalanced

Balanced

The advantage of a balanced cable is its ability to reject external interference. Therefore, it is suitable for handling a small level signal or transferring over long dis- tances. The LR16 provides the following balanced connectors.

	Inputs/outputs	Connectable connectors

	[INPUT 1-16]	XLR-3-12 connector, 3-con-
	[INPUT 1-16]	ductor TRS or 2-conductor
		ductor TRS or 2-conductor
		phone plug
	[STEREO OUT (L, R)]	XLR-3-11 connector

	[GROUP OUT 1 - 4]	2-conductor phone plug

	[PHONES]	3-conductor TRS phone plug

Unbalanced

An unbalanced cable is mainly used for handling line level signals.

The LR16 provides the following balanced connectors.

Inputs/outputs	Connectable connectors

[INSERT 1 - 8]	3-conductor TRS phone plug

[EFF SEND]	2-conductor phone plug

[AUX SEND 1 - 3]	2-conductor phone plug

[ST MIX OUT (L, R)]	RCA pin plug

[MONITOR OUT (L, R)]	2-conductor phone plug

[TAPE IN (L, R)]	RCA pin plug

Connector types

		2	1
	XLR-3-11 connector		3
	XLR-3-11 connector
	(balanced)
		1	2
			3
	XLR-3-12 connector	1	Ground
	XLR-3-12 connector	2	Hot
	(balanced)	2	Hot
	(balanced)	3	Cold
		3	Cold
			Tip
			Sleeve
	RCA pin plug	Tip	Hot
	RCA pin plug	Sleeve	Ground
	(unbalanced)	Sleeve	Ground
	(unbalanced)
			Sleeve	Tip
			Ring
		MON OUT/AUX SEND
		GROUP OUT/EFF SEND
		Tip	Hot
		Ring	Cold
		Sleeve	Ground
	3-conductor TRS phone	INSERT
	3-conductor TRS phone	Tip	Output
	plug (balanced)	Tip	Output
	plug (balanced)	Ring	Input
		Ring	Input
		Sleeve	Ground
		PHONES/INPUT
		Tip	L
		Ring	R
		Sleeve	Ground
			Tip
			Sleeve
	2-conductor phone plug	Tip	Hot
	(unbalanced)	Tip	Hot
	(unbalanced)	Sleeve	Ground
		Sleeve	Ground

20

Image 20

Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Signal flow of the mixer Connecting sources Adjusting the input level Low-cut filter Limiter EqualizerRecorder functions Recording/Playback Adding a mark Adding a mark on-the-fly Setting on the memory play setup screenPerforming memory play Recorder functions Other functions SpecificationsRecorder functions File transfer to/from a computer Introduction About power supplyPrecautions on installation About version upgrade Cleaning the exteriorCondensation About copyrightsMain features OverviewRecorder section main unit features Before using the unit Unpacking the cartonSetting the main unit and control unit separately Usage examples of LR16Integrating the main unit and control unit Mounting the main unit and control unit on the rackIntegrating the control unit and main unit Necessary itemsRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordTurning on the power Connection to external devices Connection example live recordingConnection example home recording MTRBalanced and unbalanced inputs/outputs BalancedNames and functions Control unit input channel 1 through POST/PRE switch Mute switch14 ST/1-2/3-4 assign switches Solo switchMonitor section Control unit Master channelSUB in jacks and control Recorder control section Phantom 1-8, 9-16 indicatorsInternal effects section AUX Send controls / Solo switches 24 27 EFF Send control / Solo switchAssign to Stereo OUT switches Output Limiter switchControl unit rear panel Main unit front panelNEW Project key Transport keysST MIX key REC Track Select 1-16 keysMain unit rear panel Home screen Display detailsMenu mode screen Memory play setup mode screenModel LR16 Names and functions Mixer functions Signal flow of the mixer Mixer basicsConnecting sources Adjusting the input levelConnecting sources to the input connectors Phantom power supply settingGain adjustment while monitoring EqualizerLow-cut filter LimiterUsing an external effect processor Using AUX 1, 2Pre-fader Post-faderApplying the internal effects Using the internal effects processorUsing Insert Monitoring About the effect typesChannel grouping Solo monitorUsing SUB Set the Source switches on channels 15 and 16 to TRKBlock diagram Recorder functions Recorder basics Recording/playbackRecording format Recording mode ProjectLive recording BassRecording to tracks 1 through Adjusting input level =recording level of each mixer channel PreparationAdjusting the channel output levels sent to the stereo buss RecordingPress the Play key in the recorder or mixer section Playing back a projectLocate to the beginning of the project Connecting a sound source Adjusting the input level while playing back tracks 1Overdubbing Multitrack recordingMixdown Performing overdubAdjusting level and sound of each track Starting mixdown recordingPunch in/out using the transport control keys Punch in/outPunch in/out using a footswitch At the punch out point, press only the Play keyModel LR16 Recorder functions / Recording/playback Memory play Memory Setup key in the recorder Press the Enter keySection of the main unit Numeric key number 0 through 9Selecting a channel pair for memory play Selecting the memory play modeAfter you complete assignment,press EXIT/NO key Performing memory play Press an illuminated numeric keyMark function Adding a markAdding a mark on-the-fly Adding a mark via the mark list screenLocating to a mark point Editing a markEditing a mark label Press the Enter key to bring up the Menu screenExample of label editing Editing a mark positionDeleting a mark Edit the time data in the following mannerProject management Selecting a projectCreating a new project While Select is highlighted, pressEditing a project name Use the Menu dial to highlight Rename press the Enter keyRolling back a project Name editing exampleRight Use the 3 key to enter aSaving a project to an external medium Use the Menu dial to highlight Roll back press the Enter keyExport screen details Editing the durationSelecting tracks Use the Menu dial to highlight Export press the Enter keyCopying a stereo mix file to an external medium Press any operation keySelect the files to be exported Selecting a desired fileSelecting all files Protecting a project Deleting a projectDisplay now shows the project list screen Enabling USB connection Use the Menu dial to highlight USB and press the Enter keyProtecting the internal hard disk While USB to PC is highlighted, press the Enter keyWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Adjusting the display contrast Setting the footswtich functionOther functions Press the Enter key to bring upSetting items Default Formatting the internal hard diskInitializing the system memory While holding down the Record key, press the Enter keyTo assign the destination channels of SUB Use the Menu dial to highlight Input and press the Enter keySoftware version upgrade MethodTurn on the LR16 Press the Enter key to bring up Menu screen Setting frame rate Midi synchronizationMidi message supported by the LR16 Midi connectionSetting FS/Bit of project While Default FS menu is highlighted, press the Enter keySpecifications Input and Output Main unitInput and Output Controller unit Inputs/OutputsPhysical dimensions Power Consumption approx WGeneral Main unitMidi Implementation Chart Model LR16Declaration of EC Directive Affect of Immunity on This EquipmentForthe US Customers only Fostex America Limited Warranty Shipping Index 45, 52Page Fostex CO