Fostex LR16 manual NEW Project key, Transport keys, ST MIX key, REC Track Select 1-16 keys

Page 28

Model LR16 [Names and functions]

(8) [NEW PROJECT] key

[REWIND] key

Toggles the new project mode on and off. When the new project mode is set to on, the key illuminates. In this mode, if you press the [PLAY] key while holding down the [RECORD] key, the LR16 automatically creates a new project onto the hard disk drive and starts recording.

When the transport is stopped, pressing this key fast-rewinds the transport. During play- back, pressing this key rewinds the transport at 5x speed with audible cue.

If you press this key while holding down the [STOP] key, the LR16 locates to the beginning of the project (ABS 0).

(9) Transport keys

[RECORD] key

If you press the key alone, the recorder enters record ready mode. The key starts flashing while the track meter for a record-armed track on the display shows the input level of the track.

If you press the [PLAY] key while holding down the [RECORD] key, the LR16 performs as follows depending on whether the LR16 is in new project mode or not.

When the LR16 is in new project mode:

The LR16 creates a new project and starts recording.

When the LR16 is not in new project mode:

The LR16 starts recording to the current project in insert mode.

In this condition, you can make additional recording to the project or editing such as punch in/out.

[STOP] key

Stops the transport except when memory play is being performed.

If you press the [REWIND] or [F FWD] key while holding down the [STOP] key, the LR16 performs as follows.

• [STOP] key + [REWIND] key

The LR16 locates to the beginning of the project (ABS 0).

• [STOP] key + [F FWD] key

The LR16 locates to the recording end position (REC END).

[PLAY] key

Starts playback of the current project.

<Note>: If you start playback of the project while no track is record-armed (i.e. all the [REC TRACK SELECT] keys are unlit), the LR16 automatically stops at the recording end po- sition (REC END). If you start playback while one or more tracks are record-armed, the LR16 automatically stops at 24h00m00s. If you start playback at any position after the recording end position (REC END), the LR16 locates to REC END and stops.

[F FWD] key

When the transport is stopped, pressing this key fast-forwards the transport. During play- back, pressing this key forwards the transport at 4x speed with audible cue.

If you press this key while holding down the [STOP] key, the LR16 locates to the recording end position (REC END).

(10) [ST MIX] key

You can record a stereo mix signal to the stereo mix track. This key arms or disarms the stereo mix track. When armed, the key flashes.

After recording starts, the key lights up. You can record to the stereo mix track and multitracks (1 through 16) simultaneously.

(11) [REC TRACK SELECT (1-16)] keys

Each of these keys arms or disarms the corresponding track. When armed, the key flashes. After recording starts, the key lights up.

28

Image 28
Contents Model LR16 Safety Instructions Important Safety Instructions Table of contents Signal flow of the mixer Connecting sources Adjusting the input level Low-cut filter Limiter EqualizerRecorder functions Recording/Playback Performing memory play Setting on the memory play setup screenAdding a mark Adding a mark on-the-fly Recorder functions File transfer to/from a computer SpecificationsRecorder functions Other functions Precautions on installation About power supplyIntroduction About version upgrade Cleaning the exteriorCondensation About copyrightsMain features OverviewRecorder section main unit features Before using the unit Unpacking the cartonSetting the main unit and control unit separately Usage examples of LR16Integrating the main unit and control unit Mounting the main unit and control unit on the rackIntegrating the control unit and main unit Necessary itemsRack mount adaptor After attaching the adaptor Turning on the power Connecting the power cordPreparation of power supply Connection to external devices Connection example live recordingConnection example home recording MTRBalanced and unbalanced inputs/outputs BalancedNames and functions Control unit input channel 1 through POST/PRE switch Mute switch14 ST/1-2/3-4 assign switches Solo switchSUB in jacks and control Control unit Master channelMonitor section Internal effects section Phantom 1-8, 9-16 indicators Recorder control section AUX Send controls / Solo switches 24 27 EFF Send control / Solo switchAssign to Stereo OUT switches Output Limiter switchControl unit rear panel Main unit front panelNEW Project key Transport keysST MIX key REC Track Select 1-16 keysMain unit rear panel Home screen Display detailsMenu mode screen Memory play setup mode screenModel LR16 Names and functions Mixer functions Signal flow of the mixer Mixer basicsConnecting sources Adjusting the input levelConnecting sources to the input connectors Phantom power supply settingGain adjustment while monitoring EqualizerLow-cut filter LimiterUsing an external effect processor Using AUX 1, 2Pre-fader Post-faderUsing Insert Using the internal effects processorApplying the internal effects Monitoring About the effect typesChannel grouping Solo monitorUsing SUB Set the Source switches on channels 15 and 16 to TRKBlock diagram Recorder functions Recording format Recording/playbackRecorder basics Recording mode ProjectLive recording BassRecording to tracks 1 through Adjusting input level =recording level of each mixer channel PreparationAdjusting the channel output levels sent to the stereo buss RecordingLocate to the beginning of the project Playing back a projectPress the Play key in the recorder or mixer section Connecting a sound source Adjusting the input level while playing back tracks 1Overdubbing Multitrack recordingMixdown Performing overdubAdjusting level and sound of each track Starting mixdown recordingPunch in/out using the transport control keys Punch in/outPunch in/out using a footswitch At the punch out point, press only the Play keyModel LR16 Recorder functions / Recording/playback Memory play Memory Setup key in the recorder Press the Enter keySection of the main unit Numeric key number 0 through 9After you complete assignment,press EXIT/NO key Selecting the memory play modeSelecting a channel pair for memory play Performing memory play Press an illuminated numeric keyMark function Adding a markAdding a mark on-the-fly Adding a mark via the mark list screenLocating to a mark point Editing a markEditing a mark label Press the Enter key to bring up the Menu screenExample of label editing Editing a mark positionDeleting a mark Edit the time data in the following mannerProject management Selecting a projectCreating a new project While Select is highlighted, pressEditing a project name Use the Menu dial to highlight Rename press the Enter keyRolling back a project Name editing exampleRight Use the 3 key to enter aSaving a project to an external medium Use the Menu dial to highlight Roll back press the Enter keyExport screen details Editing the durationSelecting tracks Use the Menu dial to highlight Export press the Enter keyCopying a stereo mix file to an external medium Press any operation keySelecting all files Selecting a desired fileSelect the files to be exported Protecting a project Deleting a projectDisplay now shows the project list screen Enabling USB connection Use the Menu dial to highlight USB and press the Enter keyProtecting the internal hard disk While USB to PC is highlighted, press the Enter keyWhile ? is flashing on the screen, press the Enter key LR16 ECopying data from the LR16 to a computer Adjusting the display contrast Setting the footswtich functionOther functions Press the Enter key to bring upSetting items Default Formatting the internal hard diskInitializing the system memory While holding down the Record key, press the Enter keyTo assign the destination channels of SUB Use the Menu dial to highlight Input and press the Enter keySoftware version upgrade MethodTurn on the LR16 Press the Enter key to bring up Menu screen Setting frame rate Midi synchronizationMidi message supported by the LR16 Midi connectionSetting FS/Bit of project While Default FS menu is highlighted, press the Enter keySpecifications Input and Output Main unitInput and Output Controller unit Inputs/OutputsPhysical dimensions Power Consumption approx WGeneral Main unitMidi Implementation Chart Model LR16Declaration of EC Directive Affect of Immunity on This EquipmentForthe US Customers only Fostex America Limited Warranty Shipping Index 45, 52Page Fostex CO