AMX NXM-MHS, NXC-M/ME/MPE Program Port Connections/Wiring, DB-9 Program port front panel

Page 10

Program Port Connections/Wiring

Product Information - NetLinx Modules

Program Port Connections/Wiring

Master Cards are equipped with two Program ports. One is located on the front panel and the other is on the rear for easy access. The port on the front panel is a DB-9 (male) connector, and the rear port is a 5-pin (male) connector. Use a Programming cable to connect the Program port to your PC's COM port to communicate with the Master Card. Then, you can download NetLinx programs to the Master Card with the NetLinx Studio software program. Refer to the NetLinx Studio instruction manual for programming instructions.

DB-9 Program port (front panel)

The following table shows the front panel DB-9 Program port connector, pinouts, and signals.

DB-9 Program Port, Pinouts, and Signals

DB-9 Program Port Connector	Pin	Signal
1 2 3 4 5	2	RX
	3	TX
	5	GND
6 7 8 9	7	RTS
6 7 8 9
solder side	8	CTS
solder side

5-Pin Program port (rear panel)

The table below lists the pinouts and signals for the rear panel Program port connector.

5-Pin Program Port Pinouts and Signals

Pin

Signal

1GND

2RX

3TX

4CTS

5RTS

	4	NetLinx Master Cards and Modules

Image 10

Contents NXM-MHS, NXC-M/ME/MPE NetLinx Master Cards and Modulesinstruction manual NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Product Information - NetLinx Modules Table of ContentsInstallation and Wiring NXC-M Master CardProgram Port Commands ProgrammingNetLinx Security NetLinx Security FeaturesMain Security Menu Default Security ConfigurationSetup Security Logging Into a SessionTable of Contents NXM-MHS specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsPRD Mode Settings Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode Setting the Program Port DIP Switch5-Pin Program Port Pinouts and Signals Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals DB-9 Program port front panelRear panel LEDs ICSNet/ICSHub Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only NXC-M Master Card Specifications SpecificationsNXC-M Master Card NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NXC-ME Specifications NXC-ME Master-Ethernet CardNXC-ME Master-Ethernet Card Port Type Ethernet Ports used by the MEEthernet Ports used by the ME Standard Port #NXC-MPE Specifications NXC-MPE Master Port Expander CardNXC-MPE Master Port Expander Card ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear viewSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card Mounting the Modules Into an Equipment Rack Installation and WiringMounting the Master Cards in an NXF CardFrame or NXI Preparing/connecting captive wires ICSNet RJ-45 Connections/WiringICSNet RJ-45 Pinouts/Signals ISCHub Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries PC COM Port Communication Settings Program Port CommandsProgramming Program Port CommandsProgram Port Commands Cont SET TIME ESC Pass Codes ESC Pass CodesNotes on specific Telnet/Terminal clients Windows client programsSecurity Terms Used in This Document NetLinx Security FeaturesNetLinx Security NetLinx Security FeaturesUser Name PasswordAccess Rights Group NameAccessing the Security configuration options Initial Setup via Telnet or Terminal connectionGetting connected If NetLinx master security is not enabled, you will see the following 2 Display system security options for NetLinx master Security Options Menu3 Add user 4 Edit User Edit User MenuAccess Rights Menu Access Rights MenuEdit User Menu 6 Show the list of authorized users Access Rights Menu Cont5 Delete user 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationEdit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Display Access Rights 8 Edit Group9 Delete Group 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 10 Show List of Authorized GroupsMain Security Menu Main Security MenuDefault Security Configuration Main Security Menu ContSecurity Help menu Security Help Menu OptionsLogging Into a Session Security Help Menu Options ContSetup Security LogoutHelp Security Programming AMX logo to alter specificationsPanja Inc AMX reserves