AMX NXC-M/ME/MPE instruction manual Product Information - NetLinx Modules, NXM-MHS NXM Modules

Page 7

Product Information - NetLinx Modules

Product Information - NetLinx Modules

Product Information - NetLinx Modules

NetLinx Master Cards and Modules are the controllers for NetLinx Control Systems. The Master Cards can be installed in the NetLinx CardFrame (NXF), the NetLinx Integrated Controller (NXI), or a NetLinx Module (NXS-MHS) for stand-alone operation.

The NetLinx Master Cards/Modules covered in this document are:

• NXM-MHS	NetLinx Master/Hub Module
• NXC-M	Master Card
• NXC-ME	Master-Ethernet Card
• NXC-MPE	Master Port Expander Card

NXM-MHS (NXM Modules)

NXM-MHS Modules accomodate one NetLinx Master (or Hub) Card. Master Cards can also be installed in an NXI (NetLinx Integrated Controller), or NXF (NetLinx CardFrame).

FIG. 1 shows the front panel of an NXM module. The front panels are always the same; the rear panel components are different depending on the features of the Master Card installed.

STATUS OUTPUT INPUT

PROGRAM

MASTER

FIG. 1 NXM-MHS (front)

NXM-MHS specifications

The rear panel components described here are common to all Master Cards/Modules. Components that are specific to a particular Master Card/Module are described in the Specifications section for that card.

NXM-MHS Specifications

Front Panel Components:
Program port	DB-9 (male) connector that supports RS-232 communications to your PC
	for system programming and diagnostics. You set the port's communica-
	tion speed with the Baud Rate DIP switch. See the Program Port DIP
	switch - baud rate settings section on page 2 for details.
	There are Program ports located on the front and rear panels of the Mas-
	ter Cards for easy access. Because these ports share the same circuitry,
	you should never use both ports at the same time. Doing so will result in
	communication and/or programming errors.
Status LED	Green LED blinks to indicate that the system is programmed and commu-
	nicating properly.
Output LED	Red LED blinks when the Master Card transmits data, sets channels on
	and off, sends data strings, etc.

NetLinx Master Cards and Modules	1

Image 7

Contents NetLinx Central Controllers and Cards NetLinx Master Cards and Modulesinstruction manual NXM-MHS, NXC-M/ME/MPEAMX Limited Warranty and Disclaimer NXC-M Master Card Table of ContentsInstallation and Wiring Product Information - NetLinx ModulesNetLinx Security Features ProgrammingNetLinx Security Program Port CommandsLogging Into a Session Default Security ConfigurationSetup Security Main Security MenuNetLinx Master Cards and Modules NXM-MHS Specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS specificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContSetting the Program Port DIP Switch Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode PRD Mode SettingsDB-9 Program port front panel Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals 5-Pin Program Port Pinouts and SignalsRear panel LEDs AXLink Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs ICSNet/ICSHubRear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card NXC-M Master Card SpecificationsRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Specifications NXC-ME Master-Ethernet CardNXC-ME Master-Ethernet Card Standard Port # Ethernet Ports used by the MEEthernet Ports used by the ME Port TypeNXC-MPE Specifications NXC-MPE Master Port Expander CardNXC-MPE Master Port Expander Card FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector ICSNet connectors/LEDs ICSHub In/Out connectors/LEDsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules Mounting the Modules Into an Equipment Rack Installation and WiringMounting the Master Cards in an NXF CardFrame or NXI Preparing/connecting captive wires ICSNet RJ-45 Connections/WiringICSNet RJ-45 Pinouts/Signals Ethernet RJ-45 Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ISCHub Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands Program Port CommandsProgramming PC COM Port Communication SettingsProgram Port Commands Cont SET TIME Windows client programs ESC Pass CodesNotes on specific Telnet/Terminal clients ESC Pass CodesNetLinx Security Features NetLinx Security FeaturesNetLinx Security Security Terms Used in This DocumentGroup Name PasswordAccess Rights User NameAccessing the Security configuration options Initial Setup via Telnet or Terminal connectionGetting connected If NetLinx master security is not enabled, you will see the following 2 Display system security options for NetLinx master Security Options Menu3 Add user Edit User Menu 4 Edit UserAccess Rights Menu Access Rights MenuEdit User Menu 7 Add Group Access Rights Menu Cont5 Delete user 6 Show the list of authorized usersEdit Group menu Delete directory association Edit Group Menu Add directory association8 Edit Group Edit Group menu Change Access RightsEdit Group menu Display Access Rights Edit Group menu List directory associations10 Show List of Authorized Groups 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 9 Delete GroupMain Security Menu Main Security MenuMain Security Menu Cont Default Security ConfigurationSecurity Help Menu Options Security Help menuSecurity Help Menu Options Cont Logging Into a SessionSetup Security LogoutHelp Security NetLinx Master Cards and Modules AMX reserves to alter specificationsPanja Inc AMX logo