AMX NXM-MHS Ethernet Ports used by the ME, Rear panel components, NXC-ME Master-Ethernet Card

Page 18

Ethernet Ports used by the ME

NXC-ME Master-Ethernet Card

Ethernet Ports used by the ME

Ethernet Ports used by the ME

Port Type	Description	Standard Port #

• ICSP	Peer-to-peer protocol used for both master-to-master and	1319 (UDP/TCP)
	master-to-device communications.
	For maximum flexibility, the NetLinx master can be configured
	to utilize a different port than 1319 or disable ICSP over
	Ethernet completely from either Telnet or the Program Port
	located on the NetLinx master itself.

• PING PONG	You must be able to PING an NXC-ME to be able to connect	3010
	to it over a network.

• Telnet	The NetLinx telnet server provides a mechanism to configure	23 (TCP)
	and diagnose a NetLinx system.
	For maximum flexibility, the NetLinx master can be configured
	to utilize a different port than 23 or disable Telnet completely
	from either Telnet or the Program Port located on the NetLinx
	master itself. Once disabled, the only way to enable Telnet
	again is from the NetLinx master’s program port.

• HTTP	The master has a built-in web server that complies with the	80 (TCP)
	HTTP 1.0 specification and supports all of the required fea-
	tures of HTTP v1.1.

• FTP	The NXC-ME has a built-in FTP server that conforms to	21/20 (TCP)
	RFC959.

• Internet Inside	The Internet Inside feature of the NetLinx master uses, by	10500 (TCP)
	default, port 10500 for the XML based communication proto-
	col. This port is connected to the client web browser’s JVM
	when Internet Inside control pages are retrieved from the
	NetLinx master’s web server.
	For maximum flexibility, the NetLinx master can be configured
	to utilize a different port than 10500 or to disable Internet
	Inside completely.

Rear panel components

FIG. 8 shows the rear panel components of the NXC-ME Master-Ethernet Card.

NXC-ME

Master-Ethernet

12VDC

PWR

	SPEED	FD
GND AXM AXP PWR	RTS CTS TX	RX GND
AXlink

Ethernet 10/100 connector

Ethernet 10/100 LEDs

ICSNet connectors/LEDs ICSHub IN/OUT connectors/LEDs

IN

OUT

ICSNetICSHub

PROGRAM port connector

AXLink connector

AXLink status LED (green)

12 VDC power supply connector

FIG. 8 NXC-ME Master and Ethernet Card (shown mounted in a NXS-MHS Module - rear view)

	12	NetLinx Master Cards and Modules

Image 18

Contents NXM-MHS, NXC-M/ME/MPE NetLinx Master Cards and Modulesinstruction manual NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Product Information - NetLinx Modules Table of ContentsInstallation and Wiring NXC-M Master CardProgram Port Commands ProgrammingNetLinx Security NetLinx Security FeaturesMain Security Menu Default Security ConfigurationSetup Security Logging Into a SessionTable of Contents NXM-MHS specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsPRD Mode Settings Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode Setting the Program Port DIP Switch5-Pin Program Port Pinouts and Signals Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals DB-9 Program port front panelRear panel LEDs ICSNet/ICSHub Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only NXC-M Master Card Specifications SpecificationsNXC-M Master Card NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NXC-ME Master-Ethernet Card NXC-ME SpecificationsNXC-ME Master-Ethernet Card Port Type Ethernet Ports used by the MEEthernet Ports used by the ME Standard Port #NXC-MPE Master Port Expander Card NXC-MPE SpecificationsNXC-MPE Master Port Expander Card ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear viewSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card Installation and Wiring Mounting the Modules Into an Equipment RackMounting the Master Cards in an NXF CardFrame or NXI ICSNet RJ-45 Connections/Wiring Preparing/connecting captive wiresICSNet RJ-45 Pinouts/Signals ISCHub Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries PC COM Port Communication Settings Program Port CommandsProgramming Program Port CommandsProgram Port Commands Cont SET TIME ESC Pass Codes ESC Pass CodesNotes on specific Telnet/Terminal clients Windows client programsSecurity Terms Used in This Document NetLinx Security FeaturesNetLinx Security NetLinx Security FeaturesUser Name PasswordAccess Rights Group NameInitial Setup via Telnet or Terminal connection Accessing the Security configuration optionsGetting connected If NetLinx master security is not enabled, you will see the following Security Options Menu 2 Display system security options for NetLinx master3 Add user 4 Edit User Edit User MenuAccess Rights Menu Access Rights MenuEdit User Menu 6 Show the list of authorized users Access Rights Menu Cont5 Delete user 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationEdit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Display Access Rights 8 Edit Group9 Delete Group 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 10 Show List of Authorized GroupsMain Security Menu Main Security MenuDefault Security Configuration Main Security Menu ContSecurity Help menu Security Help Menu OptionsLogging Into a Session Security Help Menu Options ContLogout Setup SecurityHelp Security Programming AMX logo to alter specificationsPanja Inc AMX reserves