AMX NXM-MHS, NXC-M/ME/MPE Installing an optional NCP-E Ethernet Card, Rear panel components

Page 14

NXC-M Master Card

Rear panel components

FIG. 4 shows the rear panel components of the NXM-M Master Card.

ICSHub IN/OUT connectors/LEDs

ICSNet connectors/LEDs

NXC-M

Master

12VDC	GND AXM AXP PWR	RTS CTS TX RX GND
	GND AXM AXP PWR	RTS CTS TX RX GND
PWR	AXlink	ICSNet	ICSHub

OUT

PROGRAM port connector

AXLink connector

AXLink status LED (green)

12 VDC power supply connector

FIG. 4 NXM-M Master Card (shown mounted in a NXS-MHS Module - rear view)

Installing an (optional) NCP-E Ethernet Card

The NXC-M Master Card has an expansion slot (port card connector) that allows you to mount an NCP-E Ethernet port card as a daughter board. Installing an NCP-E upgrades the NXC-M to an NXC-ME Master/Ethernet card.

To mount the optional NCP-E port card to the NXC-M:

1.Remove the existing rear plate from the NXC-M, as shown in FIG. 5.

NXC-M

FIG. 5 Removing the existing rear plate

2.Install the new rear plate (included with the NCP-E), as shown in FIG. 6.

	8	NetLinx Master Cards and Modules

Image 14

Contents NXM-MHS, NXC-M/ME/MPE NetLinx Master Cards and Modulesinstruction manual NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Product Information - NetLinx Modules Table of ContentsInstallation and Wiring NXC-M Master CardProgram Port Commands ProgrammingNetLinx Security NetLinx Security FeaturesMain Security Menu Default Security ConfigurationSetup Security Logging Into a SessionTable of Contents NXM-MHS specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsPRD Mode Settings Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode Setting the Program Port DIP Switch5-Pin Program Port Pinouts and Signals Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals DB-9 Program port front panelRear panel LEDs ICSNet/ICSHub Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only NXC-M Master Card Specifications SpecificationsNXC-M Master Card NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardNXC-ME Specifications Port Type Ethernet Ports used by the MEEthernet Ports used by the ME Standard Port #NXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardNXC-MPE Specifications ICSNet connectors/LEDs ICSHub In/Out connectors/LEDs SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear viewSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card Mounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires ISCHub Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries PC COM Port Communication Settings Program Port CommandsProgramming Program Port CommandsProgram Port Commands Cont SET TIME ESC Pass Codes ESC Pass CodesNotes on specific Telnet/Terminal clients Windows client programsSecurity Terms Used in This Document NetLinx Security FeaturesNetLinx Security NetLinx Security FeaturesUser Name PasswordAccess Rights Group NameGetting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master 4 Edit User Edit User MenuEdit User Menu Access Rights MenuAccess Rights Menu 6 Show the list of authorized users Access Rights Menu Cont5 Delete user 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationEdit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Display Access Rights 8 Edit Group9 Delete Group 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 10 Show List of Authorized GroupsMain Security Menu Main Security MenuDefault Security Configuration Main Security Menu ContSecurity Help menu Security Help Menu OptionsLogging Into a Session Security Help Menu Options ContHelp Security LogoutSetup Security Programming AMX logo to alter specificationsPanja Inc AMX reserves