AMX NXC-M/ME/MPE Modes and front panel LED blink patterns, Modes and LED Blink Patterns, Output

Page 11

Modes and front panel LED blink patterns

Product Information - NetLinx Modules

Modes and front panel LED blink patterns

The following table lists the modes for the Master Cards/Modules and blink patterns for the front

panel LEDs for each mode.

Modes and LED Blink Patterns

		LEDs and Blink Patterns

		STATUS	OUTPUT	INPUT
Mode	Description	(green)	(red)	(yellow)

OK	Master is functioning properly	1 Blink	Normal	Normal

Boot	Master is rebooting.	On	On	On

Missing device(s)	Master detects one or more devices	2 Blinks	Normal	Normal
	defined in the NetLinx program that are not
	present or connected to the bus.

AXlink bus failure	Master detects a communication failure on	3 Blinks	Normal	Normal
	the AXlink bus.

Contacting DHCP server	Master is contacting a DHCP server for IP	On	Off	Fast Blink
	configuration information.

Unknown DHCP server	Master could not find the DHCP server.	Fast Blink	Off	Off

Downloading program/	Downloading a program to the Master	Fast Blink	Fast Blink	Fast Blink
firmware	Card's on-board flash memory.

No program running	There is no program loaded, or the pro-	On	Normal	Normal
	gram is disabled.

Rear panel LEDs: ICSNet/ICSHub

ICSNet LED (green): lights to indicate data output activity on this port.

ICSNetICSHub

FIG. 2 Layouts of the ICSNet, ICSHub and Ethernet LEDs

ICSHub IN LED (yellow): lights to indicate data input activity on this port.

IN

OUT

ICSHub OUT LED (yellow): lights to indicate data input activity on this port.

PWR

AXP

AXM

GND

AXlink

Rear panel LEDs: AXLink

AXLink LED Blink Patterns

Blink Pattern	Description

Off	No power or the controller is not functioning properly.

1 blink per second	Normal operation. Device numbers match the programmed device numbers in
	the Axcess program.

2 blinks per second	Device numbers do not match the Axcess program, a device is not present, or
	a device is not set to the right number.

3 blinks per second	AXlink bus error. Check all AXlink bus connections.

Full on	Axcess program is not present and there is no AXlink activity.

NetLinx Master Cards and Modules	5

Image 11

Contents NetLinx Central Controllers and Cards NetLinx Master Cards and Modulesinstruction manual NXM-MHS, NXC-M/ME/MPEAMX Limited Warranty and Disclaimer NXC-M Master Card Table of ContentsInstallation and Wiring Product Information - NetLinx ModulesNetLinx Security Features ProgrammingNetLinx Security Program Port CommandsLogging Into a Session Default Security ConfigurationSetup Security Main Security MenuNetLinx Master Cards and Modules NXM-MHS Specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS specificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContSetting the Program Port DIP Switch Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode PRD Mode SettingsDB-9 Program port front panel Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals 5-Pin Program Port Pinouts and SignalsRear panel LEDs AXLink Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs ICSNet/ICSHubRear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card NXC-M Master Card SpecificationsRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardNXC-ME Specifications Standard Port # Ethernet Ports used by the MEEthernet Ports used by the ME Port TypeNXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardNXC-MPE Specifications FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector ICSNet connectors/LEDs ICSHub In/Out connectors/LEDsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules Mounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires Ethernet RJ-45 Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ISCHub Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands Program Port CommandsProgramming PC COM Port Communication SettingsProgram Port Commands Cont SET TIME Windows client programs ESC Pass CodesNotes on specific Telnet/Terminal clients ESC Pass CodesNetLinx Security Features NetLinx Security FeaturesNetLinx Security Security Terms Used in This DocumentGroup Name PasswordAccess Rights User NameGetting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master Edit User Menu 4 Edit UserEdit User Menu Access Rights MenuAccess Rights Menu 7 Add Group Access Rights Menu Cont5 Delete user 6 Show the list of authorized usersEdit Group menu Delete directory association Edit Group Menu Add directory association8 Edit Group Edit Group menu Change Access RightsEdit Group menu Display Access Rights Edit Group menu List directory associations10 Show List of Authorized Groups 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 9 Delete GroupMain Security Menu Main Security MenuMain Security Menu Cont Default Security ConfigurationSecurity Help Menu Options Security Help menuSecurity Help Menu Options Cont Logging Into a SessionHelp Security LogoutSetup Security NetLinx Master Cards and Modules AMX reserves to alter specificationsPanja Inc AMX logo