AMX NXC-M/ME/MPE, NXM-MHS instruction manual NXC-ME Master-Ethernet Card, NXC-ME Specifications

Page 17

NXC-ME Master-Ethernet Card

NXC-ME Master-Ethernet Card

NXC-ME Master-Ethernet Card

The NXM-ME Master-Ethernet Card is a NetLinx Master Card with a 10/100 Base-T TCP/IP

Ethernet connection.

Specifications

NXC-ME Specifications

Power Requirements	400 mA @ 12 VDC

Memory	• Disk on chip (Non-volatile): 8 MB (upgradeable to 32 MB)
	• SDRAM (Volatile): 16 MB
	• NVS (Non-volatile): 1 MB

LEDs:
AXlink	Green LED blinks to show AXlink data activity.
Ethernet 10/100	LEDs that show communication activity, connections, speeds, and mode information:
	• A-activity - Yellow LED blinks when receiving Ethernet data packets.
	• L-link - Green LED lights when the Ethernet cables are connected and terminated
	correctly.
	• Speed - Green LED lights when transmitting data at 100 Mbps, and is off when
	transmitting at 10 Mbps.
	• FD-full duplex - Green LED lights when running in full duplex mode, and is off when
	running half duplex mode.
ICSNet	Green LED lights when sending/receiving data.
ICSHub IN/OUT	Yellow LED lights when sending/receiving data.

Connectors:
PWR	2-pin (male) green captive-wire connector for 12 VDC power supply.
Ethernet 10/100	RJ-45 Ethernet 10/100 connector. The Ethernet Port automatically negotiates the con-
	nection speed (10 Mbps or 100 Mbps) and whether to use half duplex or full duplex
	mode.
AXlink	Black 4-pin (male) captive-wire connector that provides data and power to external con-
	trol devices.
	• Power rating = 6 A max; actual load depends on connected power supply.
PROGRAM port	5-pin (male) gray connector for system programming and diagnostics.
ICSNet	Two RJ-45 connectors that provide power and data to external ICSNet devices.
	• Power rating = 500 mA.

ICSHub In/Out	Two RJ-45 connectors that provide data to other Hubs connected to the Master Card.

Enclosure:	Metal with black matte finish.

Front Faceplate:	Plastic gray with translucent viewing window.

Dimensions (HWD):
Card(s)	0.5" x 4.8" x 8.5" (127 mm x 121.9 mm x 215.9 mm)
Module	1.5" x 5.0" x 8.8" (45 mm x 127 mm x 224 mm)

Weight:
Card only	11.2 oz (317.51 g)
With module	12.8 oz (362.87 g)

Optional accessories	• 12 VDC power supply (PSN 6.5, PSN 2.8)
	• AC-RK Accessory Rack Kit (Module)

NetLinx Master Cards and Modules	11

Image 17

Contents instruction manual NetLinx Master Cards and ModulesNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Installation and Wiring Table of ContentsProduct Information - NetLinx Modules NXC-M Master CardNetLinx Security ProgrammingProgram Port Commands NetLinx Security FeaturesSetup Security Default Security ConfigurationMain Security Menu Logging Into a SessionNetLinx Master Cards and Modules NXM-MHS NXM Modules Product Information - NetLinx ModulesNXM-MHS specifications NXM-MHS SpecificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContProgram Port DIP switch - Program Run Disable PRD mode Baud Rate SettingsPRD Mode Settings Setting the Program Port DIP SwitchDB-9 Program Port, Pinouts, and Signals Program Port Connections/Wiring5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and LED Blink Patterns Modes and front panel LED blink patternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card Specifications NXC-M Master CardRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardNXC-ME Specifications Ethernet Ports used by the ME Ethernet Ports used by the MEPort Type Standard Port #NXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardNXC-MPE Specifications Ethernet 10/100 LEDs Ethernet 10/100 connector SPE Port Connection/WiringICSNet connectors/LEDs ICSHub In/Out connectors/LEDs FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear viewSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules Mounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires Ethernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Programming Program Port CommandsPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont SET TIME Notes on specific Telnet/Terminal clients ESC Pass CodesESC Pass Codes Windows client programsNetLinx Security NetLinx Security FeaturesSecurity Terms Used in This Document NetLinx Security FeaturesAccess Rights PasswordUser Name Group NameGetting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master Edit User Menu 4 Edit UserEdit User Menu Access Rights MenuAccess Rights Menu 5 Delete user Access Rights Menu Cont6 Show the list of authorized users 7 Add GroupEdit Group menu Delete directory association Edit Group Menu Add directory associationEdit Group menu Display Access Rights Edit Group menu Change Access RightsEdit Group menu List directory associations 8 Edit Group12 Display Telnet Timeout in seconds 11 Set Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsMain Security Menu Main Security MenuMain Security Menu Cont Default Security ConfigurationSecurity Help Menu Options Security Help menuSecurity Help Menu Options Cont Logging Into a SessionHelp Security LogoutSetup Security NetLinx Master Cards and Modules Panja Inc to alter specificationsAMX logo AMX reserves