AMX NXC-M/ME/MPE, NXM-MHS NXC-MPE Master Port Expander Card, NXC-MPE Specifications

Page 19

NXC-MPE Master Port Expander Card

NXC-MPE Master Port Expander Card

NXC-MPE Master Port Expander Card

The NXC-MPE Master Port Expander Card shares the features and functionality of the NXC-ME, but with an RJ-11 SPE (Server Port Expander) connector instead of a 4-pin AXlink connector. The SPE port allows you to use the NXC-MPE in conjunction with an AXB-SPE (Server Port Expander) to control up to 12 additional AXlink bus lines of up to 3,000 feet (914.4 meters) in distance each.

Specifications

NXC-MPE Specifications

Power Requirements	1.55 A @ 12 VDC

Memory	• Disk on chip (Non-volatile): 8 MB (upgradeable to 32 MB)
	• SDRAM (Volatile): 16 MB
	• NVS (Non-volatile): 1 MB

LEDs:
AXlink (green)	Lights to show AXlink data activity
ICSNet (green)	Lights when sending/receiving data
ICSHub IN/OUT (yellow)	Lights when sending/receiving data

Connectors:
PWR	2-pin (male) green captive-wire connector for 12 VDC power supply.
Ethernet 10/100	RJ-45 Ethernet 10/100 connector. The Ethernet Port automatically negotiates the
	connection speed (10 Mbps or 100 Mbps) and whether to use half duplex or full
	duplex mode.
Expansion OUT	RJ11 connector connects to an AXB-SPE Server Port Expander.
PROGRAM port	5-pin (male) gray connector for system programming and diagnostics.
ICSNet	Two RJ-45 connectors that provide power and data to external ICSNet devices.
	• Power rating = 500 mA.
ICSHub IN/OUT	Two RJ-45 connectors that provide data to other Hubs connected to the Master
	Card.

Enclosure	Metal with black matte finish.

Front Faceplate	Plastic gray with translucent viewing window.

Dimensions (HWD):
Card(s)	0.5" x 4.8" x 8.5" (127 mm x 121.9 mm x 215.9 mm)
Module	1.5" x 5.0" x 8.8" (45 mm x 127 mm x 224 mm)

Weight:
Card only	11.2 oz (317.51 g)
With module	12.8 oz (362.87 g)

Optional accessories	• 12 VDC power supply (PSN 6.5, PSN 2.8)
	• AC-RK Accessory Rack Kit (Module)

NetLinx Master Cards and Modules	13

Image 19

Contents NetLinx Central Controllers and Cards NetLinx Master Cards and Modulesinstruction manual NXM-MHS, NXC-M/ME/MPEAMX Limited Warranty and Disclaimer NXC-M Master Card Table of ContentsInstallation and Wiring Product Information - NetLinx ModulesNetLinx Security Features ProgrammingNetLinx Security Program Port CommandsLogging Into a Session Default Security ConfigurationSetup Security Main Security MenuNetLinx Master Cards and Modules NXM-MHS Specifications Product Information - NetLinx ModulesNXM-MHS NXM Modules NXM-MHS specificationsProgram Port DIP switch - baud rate settings NXM-MHS Specifications ContSetting the Program Port DIP Switch Baud Rate SettingsProgram Port DIP switch - Program Run Disable PRD mode PRD Mode SettingsDB-9 Program port front panel Program Port Connections/WiringDB-9 Program Port, Pinouts, and Signals 5-Pin Program Port Pinouts and SignalsRear panel LEDs AXLink Modes and front panel LED blink patternsModes and LED Blink Patterns Rear panel LEDs ICSNet/ICSHubRear panel LEDs Ethernet ME and MPE only NXC-M Master Card SpecificationsNXC-M Master Card NXC-M Master Card SpecificationsRear panel components Installing an optional NCP-E Ethernet Card3. Mount the NCP-E to the NXC-M, as shown in FIG NetLinx Master Cards and Modules NXC-ME Specifications NXC-ME Master-Ethernet CardNXC-ME Master-Ethernet Card Standard Port # Ethernet Ports used by the MEEthernet Ports used by the ME Port TypeNXC-MPE Specifications NXC-MPE Master Port Expander CardNXC-MPE Master Port Expander Card FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear view SPE Port Connection/WiringEthernet 10/100 LEDs Ethernet 10/100 connector ICSNet connectors/LEDs ICSHub In/Out connectors/LEDsSPE Cable pinout information SPE Connector Pinouts and SignalsNetLinx Master Cards and Modules Mounting the Modules Into an Equipment Rack Installation and WiringMounting the Master Cards in an NXF CardFrame or NXI Preparing/connecting captive wires ICSNet RJ-45 Connections/WiringICSNet RJ-45 Pinouts/Signals Ethernet RJ-45 Pinouts and Signals ICSHub RJ-45 Connections/WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ISCHub Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands Program Port CommandsProgramming PC COM Port Communication SettingsProgram Port Commands Cont SET TIME Windows client programs ESC Pass CodesNotes on specific Telnet/Terminal clients ESC Pass CodesNetLinx Security Features NetLinx Security FeaturesNetLinx Security Security Terms Used in This DocumentGroup Name PasswordAccess Rights User NameAccessing the Security configuration options Initial Setup via Telnet or Terminal connectionGetting connected If NetLinx master security is not enabled, you will see the following 2 Display system security options for NetLinx master Security Options Menu3 Add user Edit User Menu 4 Edit UserAccess Rights Menu Access Rights MenuEdit User Menu 7 Add Group Access Rights Menu Cont5 Delete user 6 Show the list of authorized usersEdit Group menu Delete directory association Edit Group Menu Add directory association8 Edit Group Edit Group menu Change Access RightsEdit Group menu Display Access Rights Edit Group menu List directory associations10 Show List of Authorized Groups 11 Set Telnet Timeout in seconds12 Display Telnet Timeout in seconds 9 Delete GroupMain Security Menu Main Security MenuMain Security Menu Cont Default Security ConfigurationSecurity Help Menu Options Security Help menuSecurity Help Menu Options Cont Logging Into a SessionSetup Security LogoutHelp Security NetLinx Master Cards and Modules AMX reserves to alter specificationsPanja Inc AMX logo