AMX NXC-M/ME/MPE NXM-MHS Specifications Cont, Program Port DIP switch - baud rate settings

Page 8
NXM-MHS Specifications (Cont.)

Product Information - NetLinx Modules

NXM-MHS Specifications (Cont.)

Front Panel Components Cont.):

 

Input LED

Yellow LED blinks when the Master Card receives data from button

 

pushes, strings, commands, channel levels, etc.

Front Panel LEDs -

These LEDs also display special blink patterns when a mode is activated.

blink patterns

See the Modes and front panel LED blink patterns section on page 5 for

 

details.

Program Port DIP Switch

8-position DIP switch located behind the front panel for setting the baud

 

rate for the Program port. The baud rate settings are 9600, 38,400

 

(default), 57,600 and 115,200 (bps). See the Program Port DIP switch -

 

baud rate settings section on page 2 for details.

 

 

Rear Panel Components:

 

PWR connector

2-pin (male) green captive-wire connector for 12 VDC power supply

PROGRAM port

5-pin (male) gray connector for system programming and diagnostics.

 

There is a Program port located on the front and rear of the Master Cards

 

for easy access. Because these ports share the same circuitry, you

 

should never use both ports at the same time. Doing so will result in com-

 

munication and/or programming errors.

ICSNet connectors

Two RJ-45 connectors that provide power (500 mA) and data to external

 

ICSNet devices

ICSNet LEDs

Green LEDs that light when sending/receiving data on that port.

ICSHub In/Out connectors

Two RJ-45 connectors that provide data to other Hubs connected to the

 

Master Card

ICSHub IN/OUT LEDs

Yellow LEDs that light when sending/ receiving data on that port.

AXlink LED

Green LED shows AXlink/NetLink data activity

 

 

Enclosure

Metal with black matte finish

 

 

Front Faceplate

Plastic gray with translucent viewing window

 

 

Dimensions (HWD):

 

Card(s)

1.5" x 5.0" x 8.8" (45 mm x 127 mm x 224 mm)

Module

5.0" x 4.8" x 8.5" (127 mm x 121.9 mm x 215.9 mm)

 

 

Optional accessories

• 12 VDC power supply (PSN 6.5, PSN 2.8)

 

• AC-RK Accessory Rack Kit (Module)

 

 

Program Port DIP switch - baud rate settings

The Program Port DIP switch is located at the front of the Master Cards. For Modules, you must remove the front panel to access the DIP Switch.

Use this DIP switch to set the baud rate for the Program Port, according to the settings shown in the following table. Make sure the baud rate you set matches the baud rate on your PC's COM port before programming the Master Card. By default, the baud rate is set to 38,400 (bps). Note the orientation of the DIP Switch and the ON position label.

 

2

NetLinx Master Cards and Modules

 

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents NetLinx Master Cards and Modules instruction manualNXM-MHS, NXC-M/ME/MPE NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Table of Contents Installation and WiringProduct Information - NetLinx Modules NXC-M Master CardProgramming NetLinx SecurityProgram Port Commands NetLinx Security FeaturesDefault Security Configuration Setup SecurityMain Security Menu Logging Into a SessionTable of Contents Product Information - NetLinx Modules NXM-MHS NXM ModulesNXM-MHS specifications NXM-MHS SpecificationsNXM-MHS Specifications Cont Program Port DIP switch - baud rate settingsBaud Rate Settings Program Port DIP switch - Program Run Disable PRD modePRD Mode Settings Setting the Program Port DIP SwitchProgram Port Connections/Wiring DB-9 Program Port, Pinouts, and Signals5-Pin Program Port Pinouts and Signals DB-9 Program port front panelModes and front panel LED blink patterns Modes and LED Blink PatternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs AXLinkRear panel LEDs Ethernet ME and MPE only Specifications NXC-M Master CardNXC-M Master Card Specifications NXC-M Master CardInstalling an optional NCP-E Ethernet Card Rear panel components3. Mount the NCP-E to the NXC-M, as shown in FIG NXC-M Master Card NXC-ME Master-Ethernet Card NXC-ME Master-Ethernet CardNXC-ME Specifications Ethernet Ports used by the ME Ethernet Ports used by the MEPort Type Standard Port #NXC-MPE Master Port Expander Card NXC-MPE Master Port Expander CardNXC-MPE Specifications SPE Port Connection/Wiring Ethernet 10/100 LEDs Ethernet 10/100 connectorICSNet connectors/LEDs ICSHub In/Out connectors/LEDs FIG. 9 NXC-MPE Card shown mounted in a NXS-MHS Module - rear viewSPE Connector Pinouts and Signals SPE Cable pinout informationNXC-MPE Master Port Expander Card Mounting the Master Cards in an NXF CardFrame or NXI Installation and WiringMounting the Modules Into an Equipment Rack ICSNet RJ-45 Pinouts/Signals ICSNet RJ-45 Connections/WiringPreparing/connecting captive wires ICSHub RJ-45 Connections/Wiring Ethernet 10/100 Base-T RJ-45 Connections/WiringISCHub Pinouts and Signals Ethernet RJ-45 Pinouts and SignalsReplacing the Lithium Batteries Program Port Commands ProgrammingPC COM Port Communication Settings Program Port CommandsProgram Port Commands Cont SET TIME ESC Pass Codes Notes on specific Telnet/Terminal clientsESC Pass Codes Windows client programsNetLinx Security Features NetLinx SecuritySecurity Terms Used in This Document NetLinx Security FeaturesPassword Access RightsUser Name Group NameGetting connected Initial Setup via Telnet or Terminal connectionAccessing the Security configuration options If NetLinx master security is not enabled, you will see the following 3 Add user Security Options Menu2 Display system security options for NetLinx master 4 Edit User Edit User MenuEdit User Menu Access Rights MenuAccess Rights Menu Access Rights Menu Cont 5 Delete user6 Show the list of authorized users 7 Add GroupEdit Group Menu Add directory association Edit Group menu Delete directory associationEdit Group menu Change Access Rights Edit Group menu Display Access RightsEdit Group menu List directory associations 8 Edit Group11 Set Telnet Timeout in seconds 12 Display Telnet Timeout in seconds9 Delete Group 10 Show List of Authorized GroupsMain Security Menu Main Security MenuDefault Security Configuration Main Security Menu ContSecurity Help menu Security Help Menu OptionsLogging Into a Session Security Help Menu Options ContHelp Security LogoutSetup Security Programming to alter specifications Panja IncAMX logo AMX reserves
Top Page Image Contents