Heatiator C40 owner manual Don’t get enough/any heat. What can I do about it?

Page 20

4. I don’t get enough/any heat. What can I do about it?

Diagnostic Question

Possible Causes of Condition

Solutions

How much wood is used for fire?

Insufficient fuel

Make larger fires

How well seasoned is the wood?

Condition of fuel

Burn seasoned wood: (split, covered

 

 

on top minimum 6 months, preferably a

 

 

year) (about 20% moisture)

Did you install a fan?

Snap disc may be faulty

Replace snap disc

 

 

 

How much heat ouput do you expect?

• Unrealistic expectations

Replace appliance with one with greater

 

• Heat output too low for square foot-

heat output

 

age

 

How are air controls set?

Operational problems

Follow manufacturer’s instructions

5. The wood burns too fast. What can I do?

Diagnostic Question

Possible Causes of Condition

Solutions

What is the condition of the wood?

Extremely dry wood

Mix in less seasoned wood after fire

 

 

established

How are air controls set?

Operational problems

Follow manufacturer’s instructions

Fireplace won’t shut down.

ACC Timer is not working properly

Call qualified Quadra-Fire dealer

Page 20

Heatilator • Constitution EPA Fireplace • 480-1091H

4/12

Image 20
Contents C40 Hot screen/mesh and glass doors will cause burnsListing Label Information/Location 009Table of Contents Limited Lifetime Warranty Warranty Conditions Manufactured Home Approved Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Electrical Codes Glass SpecificationsNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsUser GuideYour Fireplace General Information Baffle and Blanket PlacementFirebrick Placement Moisture content Wood FuelHardwood vs. Softwood SeasoningStoring Wood Outside AirSeasoned Wood Clear Space Near the Fireplace Glass DoorsFire Safety Symptoms of Over-FiringOver-Firing Your Appliance Chimney FireStarting a Fire Burning ProcessKindling or 1st stage 2nd stageSlide Air Control Slide Left to Stop Automatic Combustion Control ACCFinal stage Manual Timer Override Burn RatesBurning Guidelines OpacityDraft Problems TroubleshootingUnderstanding Vent Problems For start-up? Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General Maintenance Creosote Chimney CleaningCare and Cleaning of Plated Surfaces Glass CleaningDisposal of Ashes Door and Door GasketMaintenance Task List Replacement Maintenance Glass ReplacementFirebrick Replacement Fire Brick ConfigurationsFan Cord Location Baffle Removal and InstallationFan Replacement Fan Replacement Instructions Removing the fanTimer Assembly Replacement 11 Timer AssemblyTimer Removal & Replacement Linkage Arm Slider Control RodHeatilator Constitution EPA Fireplace 480-1091H Service & Maintenance Log Date of Service Performed By Description of ServiceGetting Started Installer Guide Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Framing & Clearances Selecting Fireplace LocationsClearances Clearances to Combustible MaterialsFrame the Fireplace Minimum Clearances to Combustibles Within Enclosure AreaElectrical Access and Wiring Diagram Fan Wiring DiagramInstallation of Fireplace Install the Outside Air KitMm metal flex Fireplace Or rigid pipe Secure the Fireplace Place Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/ Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsInstall Ceiling Firestops Installing Flex PipeInstall Attic Insulation Shield Secure the ChimneyDouble-check the Chimney Assembly Complete InstallationInstall Flashing Cut out Hole in Roof13 Multiple Chimney Locations SL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Installations Construct the ChaseInstall Termination Cap Install Fireplace & ChimneyInstall Chase Top ST375 Square Termination Cap TCT375 Terra Cotta Cap Finishing Non-Combustible Materials Non-Combustible Facing MaterialStallation = 1/k x inches of thicknessCardboard or Metal Template Hearth ExtensionNon-Combustible Sealant Material Fireplace and Hearth Extension are flush on the floor Position the Hearth ExtensionRaised Hearth Extension Framing Non-Combustible Material Finishing MaterialCombustible Material 13 Mantel Specifications MantelAccessories Heat Zone Kit OptionalRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Constitution Fireplace DimensionsReference Materials Chimney Components Catalog Description Catalog No15-3/4 DTO134 Constitution Woodburning Fireplace Service PartsPart number list on following #3 Brick Set StockedAt Depot Door Handle Assembly Stocked at Depot Baffle Protection ChannelThis page intentionally left blank Contact Information Do not Discard this Manual
Related manuals
Manual 71 pages 32.62 Kb

C40 specifications

The Heatiator C40 is an innovative heating solution designed to optimize comfort and energy efficiency in residential and commercial spaces. This advanced heating unit combines modern technology with user-friendly features, making it an excellent choice for anyone looking to improve their heating systems.

One of the standout features of the Heatiator C40 is its powerful heating capacity. With an output of up to 40,000 BTUs, this unit is capable of efficiently warming large areas, ensuring that no space is left cold. The C40 utilizes high-efficiency burners that maximize heat output while minimizing fuel consumption. This not only translates to lower energy bills for the consumer but also contributes to a reduced carbon footprint.

The Heatiator C40 is equipped with advanced smart technology, allowing users to control their heating environment remotely. With the Heatiator mobile app, users can adjust the temperature settings, set schedules, and monitor energy usage from their smartphones. This level of control ensures that comfort is maintained without unnecessary energy waste.

Another notable characteristic of the C40 is its versatile design. The unit can be easily installed in various configurations, including wall-mounted, freestanding, or built-in options, making it suitable for any room layout or decor. Its sleek, compact design also ensures that it blends seamlessly into any environment, providing users with both functionality and aesthetic appeal.

Safety is a priority in the design of the Heatiator C40. The unit is equipped with multiple safety features, including overheat protection, a flame failure device, and an automatic shut-off system. These safety measures provide peace of mind, allowing users to enjoy their heating without worry.

Furthermore, the Heatiator C40 operates quietly, making it an ideal choice for bedrooms and living areas where noise can be a distraction. The noise-reduction technology incorporated into the unit ensures that the heating process is unobtrusive, allowing for a peaceful environment.

In summary, the Heatiator C40 is a cutting-edge heating solution that stands out due to its powerful performance, energy efficiency, and user-friendly technology. With its stylish design, safety features, and advanced controls, the C40 is an excellent investment for anyone looking to enhance their heating system while enjoying the comfort of a warm, inviting space. Whether for homes or businesses, the Heatiator C40 promises reliable performance and satisfaction.