Heatiator C40 owner manual Electrical Access and Wiring Diagram, Fan Wiring Diagram

Page 38

D. Electrical Access and Wiring Diagram

NOTICE: The manual override switch, rheostat speed con- trol and cover plate are supplied. You will need to supply: 14-3 wire with ground; 14-2 wire with ground; standard wall mount junction box; wire nuts.

1.Remove junction box cover plate on the bottom right side of the fireplace.

2.Thread the 14-3 with ground wire through the opening with the strain relief on the cover plate.

3.Match colors to wire harness, (red to red, white to white, etc) and secure with wire nuts.

NOTICE: Wiring for fans must be done before framed enclosure is completed. If using a Heat Zone kit, it also must be installed before enclosure is complete.

WARNING! Fire Risk!

Do not apply combustible finishing materials over any part of the front of this fireplace.

•The metal fireplace face may only be covered with noncombustible materials such as ceramic tile, brick, or stone.

•Do not cover or block any cooling air slots.

The decorative fascia must be removable for future service- ability of the Automatic Combustion Control.

•Maintain clearances.

•Use only non-combustible material below standoffs, material such as cement board is acceptable.

•Framing or finishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

Standard wall mount with

Junction Box

14-2 w/ground

14-3 w/ground

Match colors to wire harness (red to red,

white to white, etc) and secure with a wire nut

Power to the Fireplace

Snap Disc bypass switch

Figure 6.4 Fan Wiring Diagram

WHITE

RED

BLACK

WIRE NUT

WHITE

GREEN BLACK

Incoming Power

(110V)

Warning! Risk of Fire! You must comply with all minimum air space clearances to combustibles. Do NOT pack re-

quired air spaces with insulation or other materials.

WARNING! Fire Risk!

Comply with all minimum clearances specified.

•A minimum 1 in. (13mm) air clearance must be maintained at the back and 1 in. (25mm) to the sides of the fireplace assembly.

•Chimney sections at any level require a 2 in. (51mm) minimum air space clearance between the framing and chimney section.

Page 38

Heatilator • Constitution EPA Fireplace • 480-1091H

4/12

Page 37 Page 39
Image 38
Page 37 Page 39
Contents C40 Hot screen/mesh and glass doors will cause burnsListing Label Information/Location 009Table of Contents Limited Lifetime Warranty Warranty Conditions Manufactured Home Approved Listing and Code ApprovalsAppliance Certification Non-Combustible Materials BTU & Efficiency Specifications Electrical CodesGlass Specifications Combustible MaterialsHot glass will cause burns Operating InstructionsUser GuideYour Fireplace General Information Baffle and Blanket PlacementFirebrick Placement Hardwood vs. Softwood Moisture contentWood Fuel SeasoningStoring Wood Outside AirSeasoned Wood Clear Space Near the Fireplace Glass DoorsOver-Firing Your Appliance Fire SafetySymptoms of Over-Firing Chimney FireKindling or 1st stage Starting a FireBurning Process 2nd stageSlide Air Control Slide Left to Stop Automatic Combustion Control ACCFinal stage Burning Guidelines Manual Timer OverrideBurn Rates OpacityDraft Problems TroubleshootingUnderstanding Vent Problems For start-up? Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General Maintenance Creosote Chimney CleaningDisposal of Ashes Care and Cleaning of Plated SurfacesGlass Cleaning Door and Door GasketMaintenance Task List Replacement Maintenance Glass ReplacementFirebrick Replacement Fire Brick ConfigurationsFan Cord Location Baffle Removal and InstallationFan Replacement Fan Replacement Instructions Removing the fanTimer Assembly Replacement 11 Timer AssemblyTimer Removal & Replacement Linkage Arm Slider Control RodHeatilator Constitution EPA Fireplace 480-1091H Service & Maintenance Log Date of Service Performed By Description of ServiceGetting Started Installer Guide Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Framing & Clearances Selecting Fireplace LocationsClearances Clearances to Combustible MaterialsFrame the Fireplace Minimum Clearances to Combustibles Within Enclosure AreaElectrical Access and Wiring Diagram Fan Wiring DiagramInstallation of Fireplace Install the Outside Air KitMm metal flex Fireplace Or rigid pipe Secure the Fireplace Place Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/ Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsInstall Ceiling Firestops Installing Flex PipeInstall Attic Insulation Shield Secure the ChimneyInstall Flashing Double-check the Chimney AssemblyComplete Installation Cut out Hole in Roof13 Multiple Chimney Locations SL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Installations Construct the ChaseInstall Termination Cap Install Fireplace & ChimneyInstall Chase Top ST375 Square Termination Cap TCT375 Terra Cotta Cap Stallation FinishingNon-Combustible Materials Non-Combustible Facing Material = 1/k x inches of thicknessCardboard or Metal Template Hearth ExtensionNon-Combustible Sealant Material Fireplace and Hearth Extension are flush on the floor Position the Hearth ExtensionRaised Hearth Extension Framing Non-Combustible Material Finishing MaterialCombustible Material 13 Mantel Specifications MantelAccessories Heat Zone Kit OptionalRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Constitution Fireplace DimensionsReference Materials Chimney Components Catalog Description Catalog No15-3/4 DTO134 Constitution Woodburning Fireplace Service PartsPart number list on following #3 Brick Set StockedAt Depot Door Handle Assembly Stocked at Depot Baffle Protection ChannelThis page intentionally left blank Contact Information Do not Discard this Manual
Related manuals
Manual 71 pages 32.62 Kb

C40 specifications

The Heatiator C40 is an innovative heating solution designed to optimize comfort and energy efficiency in residential and commercial spaces. This advanced heating unit combines modern technology with user-friendly features, making it an excellent choice for anyone looking to improve their heating systems.

One of the standout features of the Heatiator C40 is its powerful heating capacity. With an output of up to 40,000 BTUs, this unit is capable of efficiently warming large areas, ensuring that no space is left cold. The C40 utilizes high-efficiency burners that maximize heat output while minimizing fuel consumption. This not only translates to lower energy bills for the consumer but also contributes to a reduced carbon footprint.

The Heatiator C40 is equipped with advanced smart technology, allowing users to control their heating environment remotely. With the Heatiator mobile app, users can adjust the temperature settings, set schedules, and monitor energy usage from their smartphones. This level of control ensures that comfort is maintained without unnecessary energy waste.

Another notable characteristic of the C40 is its versatile design. The unit can be easily installed in various configurations, including wall-mounted, freestanding, or built-in options, making it suitable for any room layout or decor. Its sleek, compact design also ensures that it blends seamlessly into any environment, providing users with both functionality and aesthetic appeal.

Safety is a priority in the design of the Heatiator C40. The unit is equipped with multiple safety features, including overheat protection, a flame failure device, and an automatic shut-off system. These safety measures provide peace of mind, allowing users to enjoy their heating without worry.

Furthermore, the Heatiator C40 operates quietly, making it an ideal choice for bedrooms and living areas where noise can be a distraction. The noise-reduction technology incorporated into the unit ensures that the heating process is unobtrusive, allowing for a peaceful environment.

In summary, the Heatiator C40 is a cutting-edge heating solution that stands out due to its powerful performance, energy efficiency, and user-friendly technology. With its stylish design, safety features, and advanced controls, the C40 is an excellent investment for anyone looking to enhance their heating system while enjoying the comfort of a warm, inviting space. Whether for homes or businesses, the Heatiator C40 promises reliable performance and satisfaction.
Top Page Image Contents