Heatiator C40 Locating Fireplace & Chimney, Frequently open doors Central heat outlets or returns

Page 33

E. Locating Fireplace & Chimney

Location of the fireplace and chimney will affect perfor- mance.

•Install within the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-down of the fire.

•Penetrate the highest part of the roof. This minimizes the effects of wind loading.

•Locate termination cap away from trees, adjacent structures, uneven roof lines and other obstructions.

•Minimize the use of chimney offsets.

•Consider the fireplace location relative to floor and ceiling and attic joists.

•Take into consideration the termination requirements in Section 8 and Section 9.

NoTICE: Locating the fireplace in a basement or in a location of considerable air movement can cause intermittent smoke spillage from fireplace. Do not locate fireplace near

•frequently open doors

•central heat outlets or returns

Location NOT recommended:

•Not the highest point of the roof

•Wind loading possible

Windward

 

Recommended Location:

Recommended Location:

•

Above peak

• Above peak

•

Inside heated space

Marginal Location:

Marginal Location:

• Wind loading possible

• Below peak

 

Recommended:

•Insulated exterior chase in cooler climates

Location NOT recommended:

•Too close to tree

•Below adjacent structure

•Lower roof line

•Avoid outside wall

Leeward

Multi-level Roofs

Figure 5.2 Recommended Chimney Locations

4/12

Heatilator • Constitution EPA Fireplace • 480-1091H

Page 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Hot screen/mesh and glass doors will cause burns C40009 Listing Label Information/LocationTable of Contents Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Appliance CertificationManufactured Home Approved Glass Specifications BTU & Efficiency Specifications Electrical CodesNon-Combustible Materials Combustible MaterialsOperating InstructionsUser Guide Your FireplaceHot glass will cause burns Baffle and Blanket Placement Firebrick PlacementGeneral Information Wood Fuel Moisture contentHardwood vs. Softwood SeasoningOutside Air Seasoned WoodStoring Wood Glass Doors Clear Space Near the FireplaceSymptoms of Over-Firing Fire SafetyOver-Firing Your Appliance Chimney FireBurning Process Starting a FireKindling or 1st stage 2nd stageAutomatic Combustion Control ACC Final stageSlide Air Control Slide Left to Stop Burn Rates Manual Timer OverrideBurning Guidelines OpacityTroubleshooting Understanding Vent ProblemsDraft Problems For start-up? Diagnostic Question Possible Causes of Condition Solutions Diagnostics and Problem SolvingDon’t get enough/any heat. What can I do about it? General Maintenance Creosote Chimney Cleaning Maintenance and Servicing the FireplaceGlass Cleaning Care and Cleaning of Plated SurfacesDisposal of Ashes Door and Door GasketReplacement Maintenance Glass Replacement Maintenance Task ListFire Brick Configurations Firebrick ReplacementBaffle Removal and Installation Fan ReplacementFan Cord Location Removing the fan Fan Replacement Instructions11 Timer Assembly Timer Assembly ReplacementLinkage Arm Slider Control Rod Timer Removal & ReplacementHeatilator Constitution EPA Fireplace 480-1091H Date of Service Performed By Description of Service Service & Maintenance LogTypical Fireplace System Getting Started Installer GuideDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Selecting Fireplace Locations Framing & ClearancesClearances to Combustible Materials ClearancesMinimum Clearances to Combustibles Within Enclosure Area Frame the FireplaceFan Wiring Diagram Electrical Access and Wiring DiagramInstall the Outside Air Kit Installation of FireplaceMm metal flex Fireplace Or rigid pipe Place Protective Metal Hearth Strips Secure the FireplaceChimney Assembly Chimney Termination Requirements Chimney RequirementsExample Using Offsets/ ReturnsAssemble the Chimney Sections Installing CAK4A and Flex PipeInstalling Flex Pipe Install Ceiling FirestopsSecure the Chimney Install Attic Insulation ShieldComplete Installation Double-check the Chimney AssemblyInstall Flashing Cut out Hole in Roof13 Multiple Chimney Locations Consult local codes for framing details SL-300 Series Ceiling/Roof ThimbleConstruct the Chase Chase InstallationsInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination Cap TCT375 Terra Cotta Cap Non-Combustible Materials Non-Combustible Facing Material FinishingStallation = 1/k x inches of thicknessHearth Extension Non-Combustible Sealant MaterialCardboard or Metal Template Position the Hearth Extension Raised Hearth Extension FramingFireplace and Hearth Extension are flush on the floor Finishing Material Combustible MaterialNon-Combustible Material Mantel 13 Mantel SpecificationsHeat Zone Kit Optional AccessoriesRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Fireplace Dimensions Reference MaterialsConstitution Catalog Description Catalog No Chimney Components15-3/4 DTO134 Service Parts Part number list on followingConstitution Woodburning Fireplace Stocked At Depot#3 Brick Set Stocked at Depot Baffle Protection Channel Door Handle AssemblyThis page intentionally left blank Do not Discard this Manual Contact Information
Related manuals
Manual 71 pages 32.62 Kb

C40 specifications

The Heatiator C40 is an innovative heating solution designed to optimize comfort and energy efficiency in residential and commercial spaces. This advanced heating unit combines modern technology with user-friendly features, making it an excellent choice for anyone looking to improve their heating systems.

One of the standout features of the Heatiator C40 is its powerful heating capacity. With an output of up to 40,000 BTUs, this unit is capable of efficiently warming large areas, ensuring that no space is left cold. The C40 utilizes high-efficiency burners that maximize heat output while minimizing fuel consumption. This not only translates to lower energy bills for the consumer but also contributes to a reduced carbon footprint.

The Heatiator C40 is equipped with advanced smart technology, allowing users to control their heating environment remotely. With the Heatiator mobile app, users can adjust the temperature settings, set schedules, and monitor energy usage from their smartphones. This level of control ensures that comfort is maintained without unnecessary energy waste.

Another notable characteristic of the C40 is its versatile design. The unit can be easily installed in various configurations, including wall-mounted, freestanding, or built-in options, making it suitable for any room layout or decor. Its sleek, compact design also ensures that it blends seamlessly into any environment, providing users with both functionality and aesthetic appeal.

Safety is a priority in the design of the Heatiator C40. The unit is equipped with multiple safety features, including overheat protection, a flame failure device, and an automatic shut-off system. These safety measures provide peace of mind, allowing users to enjoy their heating without worry.

Furthermore, the Heatiator C40 operates quietly, making it an ideal choice for bedrooms and living areas where noise can be a distraction. The noise-reduction technology incorporated into the unit ensures that the heating process is unobtrusive, allowing for a peaceful environment.

In summary, the Heatiator C40 is a cutting-edge heating solution that stands out due to its powerful performance, energy efficiency, and user-friendly technology. With its stylish design, safety features, and advanced controls, the C40 is an excellent investment for anyone looking to enhance their heating system while enjoying the comfort of a warm, inviting space. Whether for homes or businesses, the Heatiator C40 promises reliable performance and satisfaction.
Top Page Image Contents