Heatiator C40 Disposal of Ashes, Care and Cleaning of Plated Surfaces, Door and Door Gasket

Page 22

2. Disposal of Ashes

Frequency: As necessary

By: Homeowner

Task: See the following instructions.

Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a non-combustible floor or on the ground, well away from all combustible materials, pending final disposal.

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

WARNING! Fire Risk! Do not use chimney cleaners or flame colorants in your appliance. Will corrode pipe.

Warning! Risk of Fire! Ashes could contain hot embers.

WARNING! Fire Risk! Disposal of Ashes

Ashes should be placed in metal container with tight fitting lid.

Do not place metal container on combustible surface.

Ashes should be retained in closed container until all cinders have thoroughly cooled.

4. Care and Cleaning of Plated Surfaces

Clean-plated surfaces with vinegar or a glass cleaner before lighting your first fire to prevent permanent staining.

CAUTION

Do not use polishes with abrasives. It will scratch plated surfaces.

CAUTION

Clean all the fingerprints and oils from the surface before firing the appliance for the first time.

Use a glass cleaner or vinegar and towel to remove the oils.

Oils can cause permanent markings on plating, if not removed.

After plating is cured, oils will not affect the finish.

5. Door and Door Gasket

Periodically check the door gasket for proper seal. As the gasket compresses or “seats” during use, it may become necessary to adjust or tighten the door latch.

3.

Glass Cleaning

 

To Adjust or Tighten Door Latch

 

 

 

Frequency: As necessary

 

Remove spacing washers shown in Figure 4.2. At least one

 

spacing washer and the black washer must be left in place.

By: Homeowner

 

 

OR

 

Task: See the following instructions.

 

Replace the gasket material. Wear or damage to the gasket

Clean glass with a non-abrasive glass cleaner. Abrasive

material can cause air leakage into the firebox resulting in

cleaners may scratch and cause glass to crack. If the

overfiring and loss of efficiency.

deposits on the glass are not very heavy, normal glass

A replacement gasket is available from your dealer.

cleaners work well. Heavier deposits may be removed

by using a damp cloth dipped in wood ashes or by using

Latch Cam

 

a commercially available oven cleaner. After using an

Door Cross Section

oven cleaner, it is advisable to remove any residue with

(example)

 

 

a glass cleaner or soap and water. Oven cleaner left on

Locknut

 

during the next firing can permanently stain the glass and

 

Handle

damage the finish on plated metal surfaces.

 

 

 

A portion of the combustion air entering the firebox is

 

 

deflected down over the inside of the door glass. This air

 

 

flow “washes” the glass, helping to keep smoke from adher-

 

 

ing to its surface. When operated at a low burn rate, less

 

 

air will be flowing over the glass and the smoky, relatively

 

Teflon Washer

cool condition of a low fire will cause the glass to become

 

Spacing Washers

DO NOT REMOVE

coated. Operating the appliance with the Burn Rate Air

 

 

Control and Start-Up Air Control all the way open for 15-20

 

Square Key

minutes should remove the built up coating.

Figure 4.2 Door Handle Assembly

Page 22

Heatilator • Constitution EPA Fireplace • 480-1091H

4/12

Image 22
Contents C40 Hot screen/mesh and glass doors will cause burnsListing Label Information/Location 009Table of Contents Limited Lifetime Warranty Warranty Conditions Appliance Certification Listing and Code ApprovalsManufactured Home Approved Non-Combustible Materials BTU & Efficiency Specifications Electrical CodesGlass Specifications Combustible MaterialsYour Fireplace Operating InstructionsUser GuideHot glass will cause burns Firebrick Placement Baffle and Blanket PlacementGeneral Information Hardwood vs. Softwood Moisture contentWood Fuel SeasoningSeasoned Wood Outside AirStoring Wood Clear Space Near the Fireplace Glass DoorsOver-Firing Your Appliance Fire SafetySymptoms of Over-Firing Chimney FireKindling or 1st stage Starting a FireBurning Process 2nd stageFinal stage Automatic Combustion Control ACCSlide Air Control Slide Left to Stop Burning Guidelines Manual Timer OverrideBurn Rates OpacityUnderstanding Vent Problems TroubleshootingDraft Problems For start-up? Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General Maintenance Creosote Chimney CleaningDisposal of Ashes Care and Cleaning of Plated SurfacesGlass Cleaning Door and Door GasketMaintenance Task List Replacement Maintenance Glass ReplacementFirebrick Replacement Fire Brick ConfigurationsFan Replacement Baffle Removal and InstallationFan Cord Location Fan Replacement Instructions Removing the fanTimer Assembly Replacement 11 Timer AssemblyTimer Removal & Replacement Linkage Arm Slider Control RodHeatilator Constitution EPA Fireplace 480-1091H Service & Maintenance Log Date of Service Performed By Description of ServiceGetting Started Installer Guide Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Selecting Fireplace LocationsClearances Clearances to Combustible MaterialsFrame the Fireplace Minimum Clearances to Combustibles Within Enclosure AreaElectrical Access and Wiring Diagram Fan Wiring DiagramInstallation of Fireplace Install the Outside Air KitMm metal flex Fireplace Or rigid pipe Secure the Fireplace Place Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/ Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsInstall Ceiling Firestops Installing Flex PipeInstall Attic Insulation Shield Secure the ChimneyInstall Flashing Double-check the Chimney AssemblyComplete Installation Cut out Hole in Roof13 Multiple Chimney Locations SL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Installations Construct the ChaseInstall Chase Top Install Fireplace & ChimneyInstall Termination Cap ST375 Square Termination Cap TCT375 Terra Cotta Cap Stallation FinishingNon-Combustible Materials Non-Combustible Facing Material = 1/k x inches of thicknessNon-Combustible Sealant Material Hearth ExtensionCardboard or Metal Template Raised Hearth Extension Framing Position the Hearth ExtensionFireplace and Hearth Extension are flush on the floor Combustible Material Finishing MaterialNon-Combustible Material 13 Mantel Specifications MantelAccessories Heat Zone Kit OptionalRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Reference Materials Fireplace DimensionsConstitution Chimney Components Catalog Description Catalog No15-3/4 DTO134 Part number list on following Service PartsConstitution Woodburning Fireplace At Depot Stocked#3 Brick Set Door Handle Assembly Stocked at Depot Baffle Protection ChannelThis page intentionally left blank Contact Information Do not Discard this Manual
Related manuals
Manual 71 pages 32.62 Kb

C40 specifications

The Heatiator C40 is an innovative heating solution designed to optimize comfort and energy efficiency in residential and commercial spaces. This advanced heating unit combines modern technology with user-friendly features, making it an excellent choice for anyone looking to improve their heating systems.

One of the standout features of the Heatiator C40 is its powerful heating capacity. With an output of up to 40,000 BTUs, this unit is capable of efficiently warming large areas, ensuring that no space is left cold. The C40 utilizes high-efficiency burners that maximize heat output while minimizing fuel consumption. This not only translates to lower energy bills for the consumer but also contributes to a reduced carbon footprint.

The Heatiator C40 is equipped with advanced smart technology, allowing users to control their heating environment remotely. With the Heatiator mobile app, users can adjust the temperature settings, set schedules, and monitor energy usage from their smartphones. This level of control ensures that comfort is maintained without unnecessary energy waste.

Another notable characteristic of the C40 is its versatile design. The unit can be easily installed in various configurations, including wall-mounted, freestanding, or built-in options, making it suitable for any room layout or decor. Its sleek, compact design also ensures that it blends seamlessly into any environment, providing users with both functionality and aesthetic appeal.

Safety is a priority in the design of the Heatiator C40. The unit is equipped with multiple safety features, including overheat protection, a flame failure device, and an automatic shut-off system. These safety measures provide peace of mind, allowing users to enjoy their heating without worry.

Furthermore, the Heatiator C40 operates quietly, making it an ideal choice for bedrooms and living areas where noise can be a distraction. The noise-reduction technology incorporated into the unit ensures that the heating process is unobtrusive, allowing for a peaceful environment.

In summary, the Heatiator C40 is a cutting-edge heating solution that stands out due to its powerful performance, energy efficiency, and user-friendly technology. With its stylish design, safety features, and advanced controls, the C40 is an excellent investment for anyone looking to enhance their heating system while enjoying the comfort of a warm, inviting space. Whether for homes or businesses, the Heatiator C40 promises reliable performance and satisfaction.