Cisco Systems CGS 2520 manual SFP Module Patch Cable, Type of SFP Module Model

Page 14

Chapter 1 Product Overview

Ports

Table 1-2

Maximum Operating Temperature

 

 

 

Type of SFP Module

Model

 

 

 

Rugged and Industrial SFPs

GLC-SX-MM-RGD

–40 to 140°F (–40 to 60°C)

GLC-LX-SM-RGD

 

 

 

 

GLC-FE-100LX-RGD

 

 

GLC-FE-100FX-RGD

 

 

GLC-ZX-SM-RGD

 

 

 

Commercial SFPs

GLC-BX-D with digital optical monitoring

32 to 113°F (0 to 45°C)

 

(DOM) support

 

 

GLC-BX-U with DOM support

 

 

GLC-FE-100LX

 

 

GLC-FE-100BX-D

 

 

GLC-FE-100BX-U

 

 

GLC-FE-100FX

 

 

GLC-FE-100EX

 

 

GLC-FE-100ZX

 

 

CWDM SFP with DOM support

 

 

 

Extended temperature SFPs

SFP-GE-L with DOM support

23 to 140°F (–5 to 60°C)

SFP-GE-S with DOM support

 

 

 

 

SFP-GE-Z with DOM support

 

 

GLC-EX-SMD with DOM support

 

 

 

 

For information about SFP modules, see your SFP module documentation and the “Installing and Removing SFP Modules” section on page 2-19. For cable specifications, see the “SFP Module Cables” section on page B-4

SFP Module Patch Cable

The switch uses an SFP module patch cable, a 0.5-meter, copper, passive cable with SFP module connectors at each end (see Figure 1-3). The patch cable connects two switches in a cascaded configuration.

Figure 1-3 SFP Module Patch Cable

126809

For information about using the SFP module patch cable, see the “Inserting and Removing the SFP Module Patch Cable” section on page 2-21.

Cisco CGS 2520 Hardware Installation Guide

1-6

OL-31444-01

 

 

Image 14
Contents Cisco CGS 2520 Hardware Installation Guide Page N T E N T S Wall-Mounting Troubleshooting Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsProduct Overview Model Description Switch ModelsCable Side Ports Cisco CGS-2520-16S-8PC Cable-Side View10/100BASE-T Ports PoE and PoE+ PortsDual-Purpose Gigabit Ethernet Ports SFP ModulesSFP Module Patch Cable Type of SFP Module ModelAlarm Input Power-Input TerminalAlarm Ports Alarm OutputLEDs Management PortsColor System Status Switch Panel LEDsSystem LED Console LEDs Power Supply Module LEDsAlarm LEDs Color Description Port LEDsPoE LED LED Color MeaningDual-Purpose Port LEDs Power Supply SideSD Flash Memory Card SD Flash Memory Card LEDPSU OK LED Power Supply-Side LEDs Power Supply FeaturesManagement Options Network Configurations Switch Installation 140F 60C Statement 75 in .4 cm. Statement Installation GuidelinesVerifying Switch Operation Mounting Brackets Installing the SwitchMounting into a Rack Attaching Brackets for 19-Inch Racks 2shows the 23-inch rack mounting bracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks IP-30 Compliance Inserting the Rubber Plugs Inserting the Rubber Plugs Inserting the Rubber Plugs detail Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks 10 Attaching Brackets for 19-Inch RacksAttaching Brackets for Etsi Racks 11 Attaching Brackets for 23-Inch Racks12 Attaching Brackets for Etsi Racks Mounting the Switch into a Rack Wall-Mounting Attaching Brackets for Wall MountingWall-Mounting for IP-30 Compliance 14 Attaching 19-inch Rack Brackets for Wall Mounting15 Inserting the Rubber Plugs into the Switch Holes Installing and Removing SFP Modules Installing SFP Modules17 Installing an SFP Module Removing SFP ModulesInserting and Removing the SFP Module Patch Cable 18 Removing a Bale Clasp Latch SFP ModuleReplacing the SD Flash Memory Card Removing the SFP Module Patch Cable21 Loosening the Captive Screw Connecting Devices to the Ethernet Ports Device Crossover Cable Straight-Through CableConnecting to the 10/100 and 10/100/1000 Ports Connecting to the 10/100 PoE+ PortsWhere to Go Next Power Supply Installation Power Supply ModulesPower Supply Module Installation PWR-RGD-AC-DC Power Supply ModuleEquipment That You Need Installation GuidelinesInstalling a Power Supply Module Grounding the Switch Dual-hole terminal lug Installing the Power Supply Module in the Switch Loosen the Screws on the Power Supply BlankWiring the Power Source AC 5 A, DC 15 a StatementPSU2 11 Stripping the Input Power Source Wire 12 Crimping the Spade Terminal Lug Removing the Power Supply Module AC power15 Removing the Screws Switch LEDs Diagnosing ProblemsSwitch Post Results Ethernet and Fiber-Optic Cables Switch ConnectionsBad or Damaged Cable Link StatusSFP Module 10/100 and 10/100/1000 Port Connections10/100 PoE+ Port Connections Ping End Device Switch PerformanceInterface Settings Spanning Tree LoopsAuto-Negotiation and Network Interface Cards Cabling DistanceResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberEnvironmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power Supply Module Specifications Power SpecificationsConnector Specifications 10/100 Ethernet PortsSFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorDual-Purpose Ports Alarm PortAlarm Ratings Industrial and Rugged SFPs Cables and AdaptersSFP Module Cables Commercial SFPs100BASE-BX Extended temperature SFPs Cable PinoutsFigure B-6 Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device OL-31444-01 Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Entering the Initial Configuration InformationIP Settings Completing the Setup Program These choices appear