Cisco Systems CGS 2520 manual Entering the Initial Configuration Information, IP Settings

Page 88

Appendix C Configuring the Switch with the CLI Setup Program

Entering the Initial Configuration Information

Using the Setup.exe Program

Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64-bit. Click Next. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Click Next.

Step 3 When the Program Maintenance window appears, select the Remove radio button. Click Next. Step 4 When the Remove the Program window appears, click Remove.

Step 5 When the InstallShield Wizard Completed window appears, click Finish.

Uninstalling the Cisco Microsoft Windows Vista USB Driver

Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Click Next. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Click Next.

Step 3 When the Program Maintenance window appears, select the Remove radio button. Click Next. Step 4 When the Remove the Program window appears, click Remove.

Note If a User Account Control warning appears, click Allow - I trust this program to proceed.

Step 5 When the InstallShield Wizard Completed window appears, click Finish.

Entering the Initial Configuration Information

To set up the switch, you need to complete the setup program, which runs automatically after the switch powers on. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet.

IP Settings

You need this information:

Switch IP address

Subnet mask (IP netmask)

Default gateway (router)

Enable secret password

Cisco CGS 2520 Hardware Installation Guide

 

C-6

OL-31444-01

 

 

 

Image 88
Contents Cisco CGS 2520 Hardware Installation Guide Page N T E N T S Wall-Mounting Troubleshooting Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsProduct Overview Cable Side Switch ModelsModel Description Ports Cisco CGS-2520-16S-8PC Cable-Side View10/100BASE-T Ports PoE and PoE+ PortsDual-Purpose Gigabit Ethernet Ports SFP ModulesSFP Module Patch Cable Type of SFP Module ModelPower-Input Terminal Alarm PortsAlarm Input Alarm OutputLEDs Management PortsSystem LED Switch Panel LEDsColor System Status Alarm LEDs Power Supply Module LEDsConsole LEDs Port LEDs PoE LEDColor Description LED Color MeaningPower Supply Side SD Flash Memory CardDual-Purpose Port LEDs SD Flash Memory Card LEDPSU OK LED Power Supply-Side LEDs Power Supply FeaturesManagement Options Network Configurations Switch Installation 140F 60C Statement Verifying Switch Operation Installation Guidelines75 in .4 cm. Statement Mounting into a Rack Installing the SwitchMounting Brackets Attaching Brackets for 19-Inch Racks 2shows the 23-inch rack mounting bracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch Racks IP-30 Compliance Inserting the Rubber Plugs Inserting the Rubber Plugs Inserting the Rubber Plugs detail Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks 10 Attaching Brackets for 19-Inch RacksAttaching Brackets for Etsi Racks 11 Attaching Brackets for 23-Inch Racks12 Attaching Brackets for Etsi Racks Mounting the Switch into a Rack Wall-Mounting Attaching Brackets for Wall MountingWall-Mounting for IP-30 Compliance 14 Attaching 19-inch Rack Brackets for Wall Mounting15 Inserting the Rubber Plugs into the Switch Holes Installing and Removing SFP Modules Installing SFP Modules17 Installing an SFP Module Removing SFP ModulesInserting and Removing the SFP Module Patch Cable 18 Removing a Bale Clasp Latch SFP ModuleReplacing the SD Flash Memory Card Removing the SFP Module Patch Cable21 Loosening the Captive Screw Connecting Devices to the Ethernet Ports Device Crossover Cable Straight-Through CableConnecting to the 10/100 and 10/100/1000 Ports Connecting to the 10/100 PoE+ PortsWhere to Go Next Power Supply Installation Power Supply ModulesPower Supply Module Installation PWR-RGD-AC-DC Power Supply ModuleInstalling a Power Supply Module Installation GuidelinesEquipment That You Need Grounding the Switch Dual-hole terminal lug Installing the Power Supply Module in the Switch Loosen the Screws on the Power Supply BlankWiring the Power Source AC 5 A, DC 15 a StatementPSU2 11 Stripping the Input Power Source Wire 12 Crimping the Spade Terminal Lug Removing the Power Supply Module AC power15 Removing the Screws Switch Post Results Diagnosing ProblemsSwitch LEDs Switch Connections Bad or Damaged CableEthernet and Fiber-Optic Cables Link Status10/100 PoE+ Port Connections 10/100 and 10/100/1000 Port ConnectionsSFP Module Switch Performance Interface SettingsPing End Device Spanning Tree LoopsAuto-Negotiation and Network Interface Cards Cabling DistanceResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberPhysical Specifications Switch SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power Supply Module Specifications Power SpecificationsConnector Specifications 10/100 Ethernet PortsSFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Ratings Alarm PortDual-Purpose Ports Cables and Adapters SFP Module CablesIndustrial and Rugged SFPs Commercial SFPs100BASE-BX Extended temperature SFPs Cable PinoutsFigure B-6 Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device OL-31444-01 Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverIP Settings Entering the Initial Configuration InformationUninstalling the Cisco Microsoft Windows Vista USB Driver Completing the Setup Program These choices appear