Desa (V) CB36(N installation manual Hearth Access and Assembly, Removing Lower Louver Access Panel

Page 15

HEARTH ACCESS AND ASSEMBLY

Removing Lower Louver Access Panel

14

Removing Top Louver Trim Panel

Removing/Replacing Glass Door

HEARTH ACCESS AND ASSEMBLY

WARNING: If fireplace has been running, turn off and let cool before accessing or servicing the unit.

Removing Lower Louver Access Panel

1.Use your index fingers to locate the left and right spring latches found just under the top louver then draw them inward to release the pins holding the panel on the side face (see Figure 28).

2.Swing the louver panel out until it clears the fireplace opening.

3.Pull the entire panel out until the bottom tabs are free of the slot openings in the lower face frame.

2. Swing

Lower Louver

Out Panel

Access Panel

WARNING: Handle glass door panel with care. Do not strike, slam, or otherwise abuse glass. Do not operate fireplace with glass door removed, cracked, or broken.

Spring Clips

3. Pull

Out Panel

Panel Tab

Spring Latch

1.Lift Up Panel at Lower Rail

Glass Panel

Frame Rail

1. Draw Latches Inward

Locating Slot

 

Figure 28 - Removing Lower Louver Access Panel

Figure 29 - Removing/Replacing Glass Door

Removing Top Louver Trim Panel

The top louver panel may be removed for inspection and cleaning by following the instructions for removing the lower louver access panel. (see Figure 28).

Removing/Replacing Glass Door

If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame.

1.Placing a screw driver or your finger tips into the gap between the lower glass panel rail and the bottom face frame, lift the glass door assembly until the door pins clear the locating holes in the bottom face frame (see detail Figure 29).

2.Swing bottom glass panel assembly out until the door pins on the lower rail clears the bottom face frame (see Figure 30).

3.Lower the door down until the upper door pins are free of the locating holes in the spring clips and place in a safe area.

2.Swing Out Panel

3. Lower

Panel Out

Glass Panel

Frame Rail

Locating Hole

Door Pin

4. Replace glass panel in reverse order by inserting the top door

 

pins into the spring clips, lifting up at the lower frame rail,

Figure 30 - Removing/Replacing Glass Door

andlocatingthebottompinsintheholesonthelowerfaceframe.

 

 

 

 

 

 

117437-01

www.desatech.com

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this manual for future reference OWNER’S Operation and Installation ManualInch B-VENT Decorative GAS Fireplaces For Your Safety For Your Safety What to do if YOU Smell GASPage Safety Information Table of ContentsLocal Codes Product IdentificationPRE-INSTALLATION Preparation Product FeaturesPRE-INSTALATION Preparation ClearancesFraming and Finishing Mantel Clearances Unit DimensionsTypical B-Vent Configuration Installation Precautions Venting InstallationChecking for Proper Venting Venting InstallationWiring Diagrams Electronic Ignition Wiring DiagramElectrical Supply Connection Installing Remote Receiver Installing Optional ControlsInstalling Optional Wall Mount Switch GWMS2 Receiver Volt Alkaline Battery Terminal Wires Battery ClipCheck GAS Type High Altitude InstallationInstalling GAS Piping to Fireplace GAS Supply and PipingNatural From Installation Items NeededEquipment Shutoff Open Valve Closed Checking GAS ConnectionsTest Pressures In Excess of 1/2 Psig 3.5 kPa Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaRemoving/Replacing Glass Door Hearth Access and AssemblyRemoving Lower Louver Access Panel Removing Top Louver Trim PanelApplying Ember Material Installing Logs and Glowing EmbersLighting Instructions For Your Safety Read Before LightingManual Lighting Procedure Operating FireplaceOperating Fireplace Electronic Ignition System Optional Wireless Remote OperationOperating Optional GWMS2 ON/OFF Wall Mounted Switch Optional HAND-HELD Remote OperationON/OFF Series Model HRC100 Burner Flame Pattern Pilot AssemblyAIR Adjustment Setting Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersTroubleshooting Needle, or similar object toPilot unit Or cycles during operation Gas leak. See Warning statement Ment Parts, Gas leak. See Warning statement at Parts Under Warranty Replacement Parts Service HintsTechnical Service SpecificationsIllustrated Parts Breakdown VCB36NE Parts ListKEY VCB36NBurner Assembly for Models VCB36N, VCB36P Description QTY Burner Assembly for Models VCB36NE, VCB36PE KEY VCB36NE VCB36PE Description QTY Remote Control KIT WRC Series AccessoriesOWNER’S Registration Form Industrial Drive Box Bowling Green, KY 117437-01 117437-01 Page Keep this Warranty Model Serial No Date PurchasedIndustrial Drive P.O. Box
Top Page Image Contents