Desa VTGF33NRB, VTGF33PRB installation manual Remove wall switch assembly from bracket

Page 11

INSTALLATION

Continued

For Mantel Installation

If fireplace is to be installed into a mantel, (see Conventional Fireplace Installation, page 16) the wall switch assembly may be mounted on either side of the mantel, facing to the side. Do not locate wall switch assembly anywhere on the front face of the mantel.

CAUTION: Be careful of gas lines and wiring when moving floor.

1.Determine the new location for the wall switch assembly. The wires attached to switch are six feet long.

2.Remove 2 screws securing plastic wall switch assembly to bracket in fireplace lower cavity. Save screws.

3.Remove wire tie holding coiled wire attached to wall switch assembly (see Figure 8).

4.Remove wall switch assembly from bracket.

5.Carefully pass wall switch assembly and cord through large elongated hole in rear of either left or right floor support bracket, depending on desired location of switch. Pass wall switch as- sembly and cord through 1.5" diameter hole in side of fireplace outer casing (see Figure 9).

Burner

Firebox Bottom

Outlet Tube

 

Wire

 

Tie

Gas Control

Valve

Wall Switch

 

Assembly

Figure 8 - Relocating Wall Switch

Assembly

Hole in

 

Outer

Hole in Floor

Casing

Support

 

 

Bracket

Wall Switch

 

Assembly

 

Figure 9 - Routing Wall Switch Assembly

Through Fireplace for Relocation

6.Pull wall switch assembly and cord from fireplace making sure wall switch assembly will reach desired mounting location without straining cord assembly.

If you are mounting wall switch assembly to a wall, continue reading. If you are mounting your wall switch assembly to the side of the mantel, see page 12.

CAUTION: Do not apply ex- cessive pull on cord.

Mounting Wall Switch Assembly to Wall for Recessed Fireplace

7.Create three openings on wall according to Template 1, page 39. This is best done by making a pattern to work with on your wall. Carefully cut page 39 from manual and tape paper template vertically onto wall at pre- ferred location. Pierce the paper at the centers of the 2 holes with a nail or sharp pencil, leaving a mark on the wall. Do the same at centers of the four circles near the corners of the rectangle.

8.Remove paper template from wall.

9.Drill 3/8" holes at each mark.

10.Using a straight edge and pencil, connect the outer edges of the 4 holes for the rectangle (see Figure 10). This will give you cutting lines for the rectangle you will cut in the wall.

Template from Page 39

 

of This Manual

Tape

3/8"

Cutting

Lines

Diameter

 

2 Holes

 

3/4"

 

4 3/4"

Make

 

3 3/4"

Marks at

 

Centers

 

of Holes

3/8"

 

3/16"

 

Figure 10 - Using Template (Page 39) for Wall Switch Assembly Installation

113134-01B

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS Table of Contents Safety Information Product Identification AIR for Combustion Ventilation Product FeaturesLocal Codes UnpackingConfined Space and Unconfined Space Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Electrical Hookup InstallationInstallation Clearances Check GAS TypeMinimum 16 inches from Side Wall Installation SequenceRemoving Fireplace Screen and Floor Assembly For Recessed Installation Electrical Connections for Power CordRelocating Wall Switch Assembly For Mantel InstallationMounting Wall Switch Assembly to Wall for Recessed Fireplace Remove wall switch assembly from bracketMounting Wall Switch Assembly to Side of Mantel Opening in Wall or Mantel Wall Wall Switch Assembly ScrewsInstallation Items Needed Installing GAS Piping to Fireplace LocationCheck all gas connections for leaks. See Connecting Fireplace to GAS SupplyAssembly, NaturalTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Break off nailing flanges see with hammer or pliers Conventional Fireplace InstallationInserting Fireplace Into Cabinet Mantel BUILT-IN Fireplace InstallationAttaching Fireplace to Wall Studs Assembling Perimeter Trim Installing HoodInstalling Log #2 Right Log #3 Left Installing LogsOperating Fireplace Installing Battery Into RemoteInstalling Screen For Your Safety Read Before LightingNormal Lighting Instructions Using Supplied Wall Switch AssemblyUsing Hand-Held Wireless Remote Control To Turn OFF GAS To Appliance Manual Lighting Instructions for Electrical Power OutageShutting Off Heater Wall Switch Shutting Off Heater Wireless Remote ControlPilot Flame Pattern Inspecting BurnersOptional Blower Operation Operating FANBurner Injector Holders Inspected yearly by a qualified service personYou could damage the pilot assembly Burner Flame PatternsLogs Cleaning MaintenanceSpecifications Observed Problem Possible Cause Remedy TroubleshootingTurning control knob to Not enough air Check burner for dirt OperationGas regulator defective Nance, Replace regulator On windows Tilation airEnough Clean ODS/pilot seeProblem could be caused by AssemblyStatement above Gas leak. See WarningParts Under Warranty Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown KEY Part Number Description QTY Parts ListFireplace Models VTGF33NRB and VTGF33PRB 100639-01 104356-02 Not a field replacement part Accessories Fire Crackle CF6-A Extruded Louver KIT Cabinet Mantel and Full Hearth BaseLaminate Trim for Hearth or Mantel Firebox Brick Liner G8005 Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbReceiver and HAND-HELD Remote Control KIT Ghrcb Diameter Holes Diameter 2 Holes TemplatesThis page Intentionally Left Blank Wiring Diagram 113134-01B 113134-01B Limited Warranty VENT-FREE GAS Fireplace Warranty InformationKeep this Warranty

VTGF33NRB, VTGF33PRB specifications

Desa VTGF33PRB and VTGF33NRB are advanced heating solutions that combine innovative technology and design for optimal performance and user convenience. These models are well-suited for residential and commercial applications, providing efficient heating while enhancing the overall aesthetic of any space.

One of the main features of the VTGF33PRB and VTGF33NRB is their high-efficiency ratings, which allow them to deliver effective heating with minimal energy consumption. This efficiency not only helps users save on energy bills, but it also makes these models environmentally friendly, aligning with modern sustainability goals.

Both models utilize advanced infrared heating technology, which generates heat by directly warming objects and people in the room rather than heating the air. This results in a more comfortable and even distribution of warmth, providing immediate relief from cold temperatures. The infrared heating method is particularly beneficial in large or drafty spaces, as it can significantly reduce heating times and energy usage.

In terms of design, the VTGF33PRB features a sleek, modern appearance that can easily complement any décor. Its robust construction ensures durability, making it suitable for long-term usage. The VTGF33NRB, on the other hand, offers a more traditional aesthetic, perfect for those who prefer classic designs. Both models are user-friendly, designed with intuitive controls that allow for easy operation and temperature adjustments.

Another noteworthy characteristic of the Desa VTGF33 series is their safety features. Each unit is equipped with advanced safety mechanisms, including tip-over protection, overheat shut-off, and a sturdy base to prevent accidents. These safety features provide peace of mind for users, especially in households with children or pets.

The VTGF33PRB and VTGF33NRB also incorporate quiet operation technology, ensuring that heating is achieved without disruptive noise. This makes them ideal for use in bedrooms, offices, or any space where tranquility is desired.

Overall, the Desa VTGF33PRB and VTGF33NRB are exemplary models that showcase the harmonious blend of efficiency, safety, and design. Their advanced features and technologies make them reliable choices for anyone looking to enhance their heating solutions while maintaining comfort and style. With their commitment to quality and innovation, Desa continues to lead the way in the heating industry.
Top Page Image Contents