Desa VTGF33NRB, VTGF33PRB installation manual Installing Hood, Assembling Perimeter Trim

Page 19

INSTALLATION

Continued

ASSEMBLING AND ATTACHING OPTIONAL PERIMETER TRIM (Included with Mantel Accessory)

Note: The instructions below show assembling and attaching trim to fireplace.

1.Remove packaging from three pieces of trim.

2.Locate four screws, two adjusting plates with set screws, and two shims in the hard- ware packet.

3.Align shim under adjusting plate as shown in Figure 28.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 28).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side trim (see Figure 28).

6.While firmly holding edges of trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim with hanging screws on side of fireplace (see Figure 29). Push trim firmly into place, sliding hanging notches over hanging screws.

 

 

Set

 

Adjusting

Screws

 

Top Trim

Side Trim

Plate

 

 

 

Shim Slot

Slot

Mitered Edge

Figure 28 - Assembling Perimeter Trim

Trim Hanging Screws

Assembled

Trim

Hanging Notches on Trim

Figure 29 - Attaching Perimeter Trim to Fireplace

INSTALLING HOOD

Install hood to top of firebox as shown in Figure 30. Use 3 Phillips screws provided.

Figure 30 - Installing Hood to Firebox

113134-01B

www.desatech.com

19

Image 19
Contents What to do if YOU Smell GAS Table of Contents Safety Information Product Identification AIR for Combustion Ventilation Product FeaturesLocal Codes UnpackingConfined Space and Unconfined Space Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Electrical Hookup InstallationInstallation Clearances Check GAS TypeRemoving Fireplace Screen and Floor Assembly Installation SequenceMinimum 16 inches from Side Wall For Recessed Installation Electrical Connections for Power CordRelocating Wall Switch Assembly For Mantel InstallationMounting Wall Switch Assembly to Wall for Recessed Fireplace Remove wall switch assembly from bracketMounting Wall Switch Assembly to Side of Mantel Opening in Wall or Mantel Wall Wall Switch Assembly ScrewsInstallation Items Needed Installing GAS Piping to Fireplace LocationCheck all gas connections for leaks. See Connecting Fireplace to GAS SupplyAssembly, NaturalTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures In Excess Of 1/2 Psig 3.5 kPa Break off nailing flanges see with hammer or pliers Conventional Fireplace InstallationInserting Fireplace Into Cabinet Mantel BUILT-IN Fireplace InstallationAttaching Fireplace to Wall Studs Assembling Perimeter Trim Installing HoodInstalling Log #2 Right Log #3 Left Installing LogsOperating Fireplace Installing Battery Into RemoteInstalling Screen For Your Safety Read Before LightingUsing Hand-Held Wireless Remote Control Using Supplied Wall Switch AssemblyNormal Lighting Instructions To Turn OFF GAS To Appliance Manual Lighting Instructions for Electrical Power OutageShutting Off Heater Wall Switch Shutting Off Heater Wireless Remote ControlPilot Flame Pattern Inspecting BurnersOptional Blower Operation Operating FANBurner Injector Holders Inspected yearly by a qualified service personYou could damage the pilot assembly Burner Flame PatternsSpecifications Cleaning MaintenanceLogs Observed Problem Possible Cause Remedy TroubleshootingTurning control knob to Not enough air Check burner for dirt OperationGas regulator defective Nance, Replace regulator On windows Tilation airEnough Clean ODS/pilot seeProblem could be caused by AssemblyStatement above Gas leak. See WarningParts Under Warranty Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown KEY Part Number Description QTY Parts ListFireplace Models VTGF33NRB and VTGF33PRB 100639-01 104356-02 Not a field replacement part Accessories Laminate Trim for Hearth or Mantel Cabinet Mantel and Full Hearth BaseFire Crackle CF6-A Extruded Louver KIT Receiver and HAND-HELD Remote Control KIT Ghrcb Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbFirebox Brick Liner G8005 Diameter Holes Diameter 2 Holes TemplatesThis page Intentionally Left Blank Wiring Diagram 113134-01B 113134-01B Keep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS Fireplace

VTGF33NRB, VTGF33PRB specifications

Desa VTGF33PRB and VTGF33NRB are advanced heating solutions that combine innovative technology and design for optimal performance and user convenience. These models are well-suited for residential and commercial applications, providing efficient heating while enhancing the overall aesthetic of any space.

One of the main features of the VTGF33PRB and VTGF33NRB is their high-efficiency ratings, which allow them to deliver effective heating with minimal energy consumption. This efficiency not only helps users save on energy bills, but it also makes these models environmentally friendly, aligning with modern sustainability goals.

Both models utilize advanced infrared heating technology, which generates heat by directly warming objects and people in the room rather than heating the air. This results in a more comfortable and even distribution of warmth, providing immediate relief from cold temperatures. The infrared heating method is particularly beneficial in large or drafty spaces, as it can significantly reduce heating times and energy usage.

In terms of design, the VTGF33PRB features a sleek, modern appearance that can easily complement any décor. Its robust construction ensures durability, making it suitable for long-term usage. The VTGF33NRB, on the other hand, offers a more traditional aesthetic, perfect for those who prefer classic designs. Both models are user-friendly, designed with intuitive controls that allow for easy operation and temperature adjustments.

Another noteworthy characteristic of the Desa VTGF33 series is their safety features. Each unit is equipped with advanced safety mechanisms, including tip-over protection, overheat shut-off, and a sturdy base to prevent accidents. These safety features provide peace of mind for users, especially in households with children or pets.

The VTGF33PRB and VTGF33NRB also incorporate quiet operation technology, ensuring that heating is achieved without disruptive noise. This makes them ideal for use in bedrooms, offices, or any space where tranquility is desired.

Overall, the Desa VTGF33PRB and VTGF33NRB are exemplary models that showcase the harmonious blend of efficiency, safety, and design. Their advanced features and technologies make them reliable choices for anyone looking to enhance their heating solutions while maintaining comfort and style. With their commitment to quality and innovation, Desa continues to lead the way in the heating industry.