Invacare 1143206 manual Charging Batteries, Disconnecting Battery Cables

Page 63

SECTION 13—BATTERIES

Disconnecting Battery Cables

WARNING

The use of rubber gloves is recommended when working with batteries.

NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery terminal(s)/post(s) at the same time. An electrical short may occur and serious per- sonal injury or damage may occur.

NOTE: For this procedure, refer to FIGURE 13.2 on page 62 and FIGURE 13.3 on page 63.

1.Remove the seat. Refer to Removing/Installing the Seat Assembly on page 37.

2.Remove the batteries. Refer to Removing/Installing the Batteries on page 59.

3.Cut the tie‐wrap that secures the battery terminal cap in place (Detail “B” of FIGURE 13.2).

4.Slide terminal cap(s) UP on the battery cable(s) (FIGURE 13.3).

5.Disconnect POSITIVE (+) RED battery cable from the POSITIVE (+) battery terminal/ post (FIGURE 13.2).

6.Disconnect NEGATIVE (‐) BLACK battery cable from NEGATIVE (‐) battery terminal/ post (FIGURE 13.2).

Battery

Battery

Terminal Cap

Cable

 

FIGURE 13.3 Battery Terminal Caps

Charging Batteries

WARNING

NEVER attempt to recharge the batteries by attaching cables directly to the battery terminals.

DO NOT attempt to recharge the batteries and operate the wheelchair at the same time.

DO NOT attempt to recharge the batteries when the wheelchair has been exposed to any type of moisture.

DO NOT attempt to recharge the batteries when the wheelchair is outside. DO NOT sit in the wheelchair while recharging the batteries.

Read and carefully follow the individual instructions for each charger (supplied or purchased). If charging instructions are not supplied, consult a qualified technician for proper procedures.

Part No. 1143206

63

Pronto® M41 with SureStep®

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Pronto M41 With SureStep Reference Documents Accessories WarningTable of Contents Arms Batteries Meaning Special NotesSpecial Notes Positive + Label LocationFOLD-DOWN Typical Product ParametersTypical Product Parameters FOLD-DOWN Operation Information Controller Settings/Repair or ServiceAccessories Information General GuidelinesGeneral Guidelines Charging Batteries BatteriesRain Test Weight TrainingWeight Limitation Grounding InstructionsEMI Information EMI Information Setup Checklist Initial SetupStability and Balance SAFETY/HANDLING of WheelchairsCoping With Everyday Obstacles Coping With Everyday ObstaclesLifting/Stairways Pinch PointsLifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching and Bending Backward Reaching, Leaning and Bending ForwardSafety Inspection Safety Inspection ChecklistsInspect/Adjust Initially Inspect/Adjust Monthly Inspect/Adjust WeeklyTroubleshooting Guide Inspect/Adjust PeriodicallyAll Wheelchairs SPJ+ Joysticks Troubleshooting ElectricalInformation Gauge Display Diagnostics Wheelchair Operation Turning the Power On/OffMovement Action Using the Joystick to Drive the WheelchairMK5 SPJ-INT Joystick Switches and Indicators On/Off ButtonSpeedometer Speed Control Buttons JoystickCharger/Programming Input Information Gauge Display Service IndicatorArms Removing/Installing the ArmsAdjusting the Arms Adjusting WidthAdjusting Angle Adjusting Depth Fold Down Back Seats Only Adjusting Height Semi-Recline Seats OnlyRemoving Removing/Installing the Seat AssemblyInstalling SeatAdjusting the Headrest Adjusting the Back Angle Semi-Recline BackBack seat shown Replacing the Seat Positioning StrapRemoving/Installing the Footboard Assembly Footboard AssemblyAngle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly DepthHeight Adjusting the Footboard Assembly HeightFront Riggings Installing/Removing Front RiggingsModel PHWH93 Adjusting Footrest HeightModel PH904A and PHAL4A Replacing Heel LoopsRaising/Lowering Elevating Front Riggings Adjusting/Replacing Telescoping Front Rigging SupportsFront Rigging Removing/Installing the Top Shroud Shroud and WheelsReplacing the Flat Free Tires on the Wheel Rim Removing/Installing the Rear Shroud Engaging/Disengaging Motor Release Lever Removing/Installing CastersRemoving/Installing Casters Adjusting ForksAdjusting Anti-Dive Springs Removing/Installing Forks and/or Caster AssembliesElectronics Removing/Installing the Joystick AssemblyRepositioning the Joystick Removing/Installing the Joystick AssemblyDisconnecting/Connecting the Joystick Disconnecting the JoystickConnecting the Joystick Disconnecting/Connecting the Joystick Batteries Using the Proper BatteriesRemoving/Installing the Batteries Removing/Installing the Batteries Connecting Battery Cables Connecting/Disconnecting Battery CablesTerminal CapNOTE Handles on batteries removed for clarity Charging Batteries Disconnecting Battery CablesBattery Charger Operation Battery Charger Operation Installing/Removing the Crutch/Cane Holder AccessoriesInstalling/Removing the Oxygen Holder Installing/Removing the Walker Holder Installing/Removing/Using the Walker HolderInstalling/Removing/Using the Walker Holder Using the Walker HolderPronto M41 with SureStep Global Limited Warranty Excluding Canada USA Canada Limited Warranty

1143206 specifications

The Invacare 1143206 is a highly regarded mobility product recognized for its robust design and advanced features, specifically tailored to enhance user comfort and mobility. This wheelchair is engineered with both user needs and caregiver requirements in mind, ensuring an optimal blend of functionality, durability, and ease of use.

One of the standout features of the Invacare 1143206 is its adjustable seating system. This innovative design allows users to customize the seating position according to their individual needs. The seat height can be adjusted easily, accommodating a variety of users and enhancing accessibility for those with different heights. The backrest is also adjustable, providing additional support for the user, which is essential for long-term comfort.

The wheelchair is constructed from high-quality materials to ensure longevity and reliability. The frame is made from sturdy steel, which not only supports the user effectively but also contributes to the overall stability of the chair. The innovative design minimizes the risk of tipping and enhances safety, particularly when navigating uneven surfaces.

Invacare has integrated several technologies to enhance the user experience, including advanced wheel and tire designs that offer superior grip and maneuverability. The footrests are swing-away and adjustable, allowing users to enter and exit the chair with ease.

Another important characteristic of the Invacare 1143206 is its lightweight structure. While the frame is sturdy, it is also designed to be easily transportable. This makes it ideal for users who may need to load it into vehicles or transport it for outings, as caregivers can do so without significant effort.

Safety is paramount in the engineering of the Invacare 1143206. The wheelchair features reliable brakes and locking mechanisms that allow for secure positioning during use. Additionally, the wheels are designed to prevent accidental rolling, making it a safe choice for both users and caregivers.

In summary, the Invacare 1143206 is a thoughtfully designed wheelchair that encompasses a range of essential features and technologies. Its adjustable seating system, lightweight structure, ergonomic design, and safety features collectively make it a preferred choice for users seeking comfort and mobility solutions. Whether for daily use or occasional outings, this wheelchair stands out as a dependable and versatile option.
Top Page Image Contents