Invacare 1143206 manual Accessories, Installing/Removing the Crutch/Cane Holder

Page 66

SECTION 14—ACCESSORIES

SECTION 14—ACCESSORIES

WARNING

After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.

Before performing any maintenance, adjustment or service verify that on/off switch on the joystick is in the off position.

Installing/Removing the Crutch/Cane Holder

WARNING

The installation of the crutch/cane holder onto the back of the seat significantly increases the length of the wheelchair. When turning the wheelchair or swiveling the wheelchair seat, it is important to take note of this increased length - otherwise, injury and/or damage to the surrounding property may result.

NOTE: For this procedure, refer to FIGURE 14.1.

NOTE: The Crutch/Cane Holder, Oxygen Holder, and Walker Holder all install into the accessory tube. Only one of these may be installed at a time.

NOTE: To remove, reverse the following procedure.

Installing

1.If necessary, loosen but do not remove the mounting knob.

2.Install the crutch/cane holder into the accessory tube located on the back of the seat.

3.Thread the mounting knob into the welded nut on the accessory tube. Securely tighten.

4.Align slot on base with hook on crutch/cane holder and slide base down into position.

 

Seat

 

Accessory

Crutch/Cane

Tube

Holder

 

Hook

 

 

Mounting

Base

Knob

FIGURE 14.1 Installing/Removing the Crutch/Cane Holder

Pronto® M41 with SureStep®

66

Part No. 1143206

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Pronto M41 With SureStep Accessories Warning Reference DocumentsTable of Contents Arms Batteries Special Notes MeaningSpecial Notes Label Location Positive +Typical Product Parameters FOLD-DOWNTypical Product Parameters FOLD-DOWN General Guidelines Controller Settings/Repair or ServiceAccessories Information Operation InformationGeneral Guidelines Batteries Charging BatteriesGrounding Instructions Weight TrainingWeight Limitation Rain TestEMI Information EMI Information Initial Setup Setup ChecklistSAFETY/HANDLING of Wheelchairs Stability and BalanceCoping With Everyday Obstacles Coping With Everyday ObstaclesPinch Points Lifting/StairwaysLifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching, Leaning and Bending Forward Reaching and Bending BackwardSafety Inspection Safety Inspection ChecklistsInspect/Adjust Initially Inspect/Adjust Weekly Inspect/Adjust MonthlyTroubleshooting Guide Inspect/Adjust PeriodicallyAll Wheelchairs Troubleshooting Electrical SPJ+ JoysticksInformation Gauge Display Diagnostics Turning the Power On/Off Wheelchair OperationUsing the Joystick to Drive the Wheelchair Movement ActionMK5 SPJ-INT Joystick Switches and Indicators On/Off ButtonSpeedometer Speed Control Buttons JoystickCharger/Programming Input Service Indicator Information Gauge DisplayRemoving/Installing the Arms ArmsAdjusting the Arms Adjusting WidthAdjusting Angle Adjusting Height Semi-Recline Seats Only Adjusting Depth Fold Down Back Seats OnlySeat Removing/Installing the Seat AssemblyInstalling RemovingAdjusting the Back Angle Semi-Recline Back Adjusting the HeadrestReplacing the Seat Positioning Strap Back seat shownFootboard Assembly Removing/Installing the Footboard AssemblyAdjusting the Footboard Assembly AngleAdjusting the Footboard Assembly Depth DepthAdjusting the Footboard Assembly Height HeightInstalling/Removing Front Riggings Front RiggingsAdjusting Footrest Height Model PHWH93Replacing Heel Loops Model PH904A and PHAL4AAdjusting/Replacing Telescoping Front Rigging Supports Raising/Lowering Elevating Front RiggingsFront Rigging Removing/Installing the Top Shroud Shroud and WheelsReplacing the Flat Free Tires on the Wheel Rim Removing/Installing the Rear Shroud Removing/Installing Casters Engaging/Disengaging Motor Release LeverAdjusting Forks Removing/Installing CastersRemoving/Installing Forks and/or Caster Assemblies Adjusting Anti-Dive SpringsRemoving/Installing the Joystick Assembly ElectronicsRemoving/Installing the Joystick Assembly Repositioning the JoystickDisconnecting/Connecting the Joystick Disconnecting the JoystickConnecting the Joystick Disconnecting/Connecting the Joystick Using the Proper Batteries BatteriesRemoving/Installing the Batteries Removing/Installing the Batteries Connecting/Disconnecting Battery Cables Connecting Battery CablesTerminal CapNOTE Handles on batteries removed for clarity Disconnecting Battery Cables Charging BatteriesBattery Charger Operation Battery Charger Operation Accessories Installing/Removing the Crutch/Cane HolderInstalling/Removing the Oxygen Holder Installing/Removing/Using the Walker Holder Installing/Removing the Walker HolderUsing the Walker Holder Installing/Removing/Using the Walker HolderPronto M41 with SureStep Global Limited Warranty Excluding Canada Canada Limited Warranty USA

1143206 specifications

The Invacare 1143206 is a highly regarded mobility product recognized for its robust design and advanced features, specifically tailored to enhance user comfort and mobility. This wheelchair is engineered with both user needs and caregiver requirements in mind, ensuring an optimal blend of functionality, durability, and ease of use.

One of the standout features of the Invacare 1143206 is its adjustable seating system. This innovative design allows users to customize the seating position according to their individual needs. The seat height can be adjusted easily, accommodating a variety of users and enhancing accessibility for those with different heights. The backrest is also adjustable, providing additional support for the user, which is essential for long-term comfort.

The wheelchair is constructed from high-quality materials to ensure longevity and reliability. The frame is made from sturdy steel, which not only supports the user effectively but also contributes to the overall stability of the chair. The innovative design minimizes the risk of tipping and enhances safety, particularly when navigating uneven surfaces.

Invacare has integrated several technologies to enhance the user experience, including advanced wheel and tire designs that offer superior grip and maneuverability. The footrests are swing-away and adjustable, allowing users to enter and exit the chair with ease.

Another important characteristic of the Invacare 1143206 is its lightweight structure. While the frame is sturdy, it is also designed to be easily transportable. This makes it ideal for users who may need to load it into vehicles or transport it for outings, as caregivers can do so without significant effort.

Safety is paramount in the engineering of the Invacare 1143206. The wheelchair features reliable brakes and locking mechanisms that allow for secure positioning during use. Additionally, the wheels are designed to prevent accidental rolling, making it a safe choice for both users and caregivers.

In summary, the Invacare 1143206 is a thoughtfully designed wheelchair that encompasses a range of essential features and technologies. Its adjustable seating system, lightweight structure, ergonomic design, and safety features collectively make it a preferred choice for users seeking comfort and mobility solutions. Whether for daily use or occasional outings, this wheelchair stands out as a dependable and versatile option.
Top Page Image Contents