Invacare 1143206 manual Troubleshooting Electrical, SPJ+ Joysticks

Page 27

 

 

SECTION 5—SAFETY INSPECTION

 

 

 

SYMPTOM

PROBABLE CAUSE

SOLUTIONS

 

 

 

Wheelchair will not drive.

Motor release levers are

Engage motor release levers.

 

disengaged.

 

 

Batteries require charging.

Charge batteries. Make sure the setting on the

 

 

charger is correct.

 

Charger plugged in.

Unplug charger from wall outlet before

 

 

operating the wheelchair.

 

Circuit breaker tripped.

Reset circuit breaker. If breaker trips again, it

 

 

may indicate need for internal repair. Contact

 

 

Dealer/Invacare.

 

 

 

Motor “chatters” or runs

Electrical malfunction.

Contact Dealer/Invacare.

irregularly.

 

 

 

 

 

Only one drive wheel turns.

Electrical malfunction.

Contact Dealer/Invacare for service.

 

One motor lock is

Engage motor lock.

 

disengaged.

 

 

 

 

Joystick erratic or does not

Electrical malfunction.

Contact Dealer/Invacare for service.

respond as desired.

Controller programmed

Reprogram controller (Refer to electronics

 

improperly.

manual supplied with wheelchair).

 

 

 

Wheelchair does not

Poor battery terminal

Have terminals cleaned.

respond to commands.

connection.

 

 

 

 

Power indicator off - even

Electrical malfunction.

Contact Dealer/Invacare for service.

after recharging.

 

 

 

 

 

Troubleshooting - Electrical

NOTE: For additional troubleshooting information and explanation of error codes, refer to the individual Electronics Manual supplied with each wheelchair.

SPJ+ Joysticks

The joystick information gauge and the service indicator give indications of the type of fault or error detected by the control module. When a fault is detected, the wheelchair may stop and not drive. The LEDs on the information gauge may flash in a particular pattern or the service indicator light will flash. The number or type of flashes indicates the nature of the error. If multiple errors are found, only the first error encountered by the control module will be displayed.

Part No. 1143206

27

Pronto® M41 with SureStep®

Image 27
Contents Pronto M41 With SureStep Reference Documents Accessories WarningTable of Contents Arms Batteries Meaning Special NotesSpecial Notes Positive + Label LocationFOLD-DOWN Typical Product ParametersTypical Product Parameters FOLD-DOWN Operation Information Controller Settings/Repair or ServiceAccessories Information General GuidelinesGeneral Guidelines Charging Batteries BatteriesRain Test Weight TrainingWeight Limitation Grounding InstructionsEMI Information EMI Information Setup Checklist Initial SetupStability and Balance SAFETY/HANDLING of WheelchairsCoping With Everyday Obstacles Coping With Everyday ObstaclesLifting/Stairways Pinch PointsLifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching and Bending Backward Reaching, Leaning and Bending ForwardSafety Inspection Safety Inspection ChecklistsInspect/Adjust Initially Inspect/Adjust Monthly Inspect/Adjust WeeklyTroubleshooting Guide Inspect/Adjust PeriodicallyAll Wheelchairs SPJ+ Joysticks Troubleshooting ElectricalInformation Gauge Display Diagnostics Wheelchair Operation Turning the Power On/OffMovement Action Using the Joystick to Drive the WheelchairMK5 SPJ-INT Joystick Switches and Indicators On/Off ButtonSpeedometer Speed Control Buttons JoystickCharger/Programming Input Information Gauge Display Service IndicatorArms Removing/Installing the ArmsAdjusting the Arms Adjusting WidthAdjusting Angle Adjusting Depth Fold Down Back Seats Only Adjusting Height Semi-Recline Seats OnlyRemoving Removing/Installing the Seat AssemblyInstalling SeatAdjusting the Headrest Adjusting the Back Angle Semi-Recline BackBack seat shown Replacing the Seat Positioning StrapRemoving/Installing the Footboard Assembly Footboard AssemblyAngle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly DepthHeight Adjusting the Footboard Assembly HeightFront Riggings Installing/Removing Front RiggingsModel PHWH93 Adjusting Footrest HeightModel PH904A and PHAL4A Replacing Heel LoopsRaising/Lowering Elevating Front Riggings Adjusting/Replacing Telescoping Front Rigging SupportsFront Rigging Removing/Installing the Top Shroud Shroud and WheelsReplacing the Flat Free Tires on the Wheel Rim Removing/Installing the Rear Shroud Engaging/Disengaging Motor Release Lever Removing/Installing CastersRemoving/Installing Casters Adjusting ForksAdjusting Anti-Dive Springs Removing/Installing Forks and/or Caster AssembliesElectronics Removing/Installing the Joystick AssemblyRepositioning the Joystick Removing/Installing the Joystick AssemblyDisconnecting/Connecting the Joystick Disconnecting the JoystickConnecting the Joystick Disconnecting/Connecting the Joystick Batteries Using the Proper BatteriesRemoving/Installing the Batteries Removing/Installing the Batteries Connecting Battery Cables Connecting/Disconnecting Battery CablesTerminal CapNOTE Handles on batteries removed for clarity Charging Batteries Disconnecting Battery CablesBattery Charger Operation Battery Charger Operation Installing/Removing the Crutch/Cane Holder AccessoriesInstalling/Removing the Oxygen Holder Installing/Removing the Walker Holder Installing/Removing/Using the Walker HolderInstalling/Removing/Using the Walker Holder Using the Walker HolderPronto M41 with SureStep Global Limited Warranty Excluding Canada USA Canada Limited Warranty

1143206 specifications

The Invacare 1143206 is a highly regarded mobility product recognized for its robust design and advanced features, specifically tailored to enhance user comfort and mobility. This wheelchair is engineered with both user needs and caregiver requirements in mind, ensuring an optimal blend of functionality, durability, and ease of use.

One of the standout features of the Invacare 1143206 is its adjustable seating system. This innovative design allows users to customize the seating position according to their individual needs. The seat height can be adjusted easily, accommodating a variety of users and enhancing accessibility for those with different heights. The backrest is also adjustable, providing additional support for the user, which is essential for long-term comfort.

The wheelchair is constructed from high-quality materials to ensure longevity and reliability. The frame is made from sturdy steel, which not only supports the user effectively but also contributes to the overall stability of the chair. The innovative design minimizes the risk of tipping and enhances safety, particularly when navigating uneven surfaces.

Invacare has integrated several technologies to enhance the user experience, including advanced wheel and tire designs that offer superior grip and maneuverability. The footrests are swing-away and adjustable, allowing users to enter and exit the chair with ease.

Another important characteristic of the Invacare 1143206 is its lightweight structure. While the frame is sturdy, it is also designed to be easily transportable. This makes it ideal for users who may need to load it into vehicles or transport it for outings, as caregivers can do so without significant effort.

Safety is paramount in the engineering of the Invacare 1143206. The wheelchair features reliable brakes and locking mechanisms that allow for secure positioning during use. Additionally, the wheels are designed to prevent accidental rolling, making it a safe choice for both users and caregivers.

In summary, the Invacare 1143206 is a thoughtfully designed wheelchair that encompasses a range of essential features and technologies. Its adjustable seating system, lightweight structure, ergonomic design, and safety features collectively make it a preferred choice for users seeking comfort and mobility solutions. Whether for daily use or occasional outings, this wheelchair stands out as a dependable and versatile option.