Invacare 1143206 manual Installing/Removing/Using the Walker Holder

Page 68

SECTION 14—ACCESSORIES

Clamp

Protective Caps

 

 

 

 

 

Knob

 

 

 

 

Welded Nut

 

 

 

Clamp

 

Upper Support

 

Knob

 

Clamp

 

 

Accessory

Knob

Welded

 

Mounting

Tube

 

Nut

 

Tube

 

 

 

 

 

 

 

Mounting Nut

Lower Support

 

 

Welded Nut

 

 

 

Protective

 

 

Mounting Bolt

Caps

 

Clamp

Mounting Hand

NOTE: Seat not shown.

 

 

Knob

Knob

FIGURE 14.2 Installing/Removing the Oxygen Holder

Installing/Removing/Using the Walker Holder

INSTALLATION WARNINGS

After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely.

The installation of the walker holder onto the back of the wheelchair seat increases the length of the wheelchair up to nine inches. When turning the wheelchair it is important to take note of this increased length - otherwise, injury and/or damage to surrounding property may result.

NOTE: For this procedure, refer to FIGURE 14.3 on page 69.

Installing/Removing the Walker Holder

NOTE: Reverse this procedure to remove the walker holder.

NOTE: The Crutch/Cane Holder, Oxygen Holder, and Walker Holder all install into the accessory tube. Only one of these may be installed at a time.

1.If necessary, loosen but do not remove the mounting knob.

2.Install the walker holder into the accessory tube.

3.Thread the mounting knob into the welded nut on the accessory tube. Securely tighten.

Pronto® M41 with SureStep®

68

Part No. 1143206

Image 68
Contents Pronto M41 With SureStep Accessories Warning Reference DocumentsTable of Contents Arms Batteries Special Notes MeaningSpecial Notes Label Location Positive +Typical Product Parameters FOLD-DOWNTypical Product Parameters FOLD-DOWN Controller Settings/Repair or Service Accessories InformationGeneral Guidelines Operation InformationGeneral Guidelines Batteries Charging BatteriesWeight Training Weight LimitationGrounding Instructions Rain TestEMI Information EMI Information Initial Setup Setup ChecklistSAFETY/HANDLING of Wheelchairs Stability and BalanceCoping With Everyday Obstacles Coping With Everyday ObstaclesPinch Points Lifting/StairwaysLifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching, Leaning and Bending Forward Reaching and Bending BackwardInspect/Adjust Initially Safety InspectionSafety Inspection Checklists Inspect/Adjust Weekly Inspect/Adjust MonthlyAll Wheelchairs Troubleshooting GuideInspect/Adjust Periodically Troubleshooting Electrical SPJ+ JoysticksInformation Gauge Display Diagnostics Turning the Power On/Off Wheelchair OperationUsing the Joystick to Drive the Wheelchair Movement ActionSpeedometer MK5 SPJ-INT Joystick Switches and IndicatorsOn/Off Button Charger/Programming Input Speed Control ButtonsJoystick Service Indicator Information Gauge DisplayRemoving/Installing the Arms ArmsAdjusting Angle Adjusting the ArmsAdjusting Width Adjusting Height Semi-Recline Seats Only Adjusting Depth Fold Down Back Seats OnlyRemoving/Installing the Seat Assembly InstallingSeat RemovingAdjusting the Back Angle Semi-Recline Back Adjusting the HeadrestReplacing the Seat Positioning Strap Back seat shownFootboard Assembly Removing/Installing the Footboard AssemblyAdjusting the Footboard Assembly AngleAdjusting the Footboard Assembly Depth DepthAdjusting the Footboard Assembly Height HeightInstalling/Removing Front Riggings Front RiggingsAdjusting Footrest Height Model PHWH93Replacing Heel Loops Model PH904A and PHAL4AAdjusting/Replacing Telescoping Front Rigging Supports Raising/Lowering Elevating Front RiggingsFront Rigging Replacing the Flat Free Tires on the Wheel Rim Removing/Installing the Top ShroudShroud and Wheels Removing/Installing the Rear Shroud Removing/Installing Casters Engaging/Disengaging Motor Release LeverAdjusting Forks Removing/Installing CastersRemoving/Installing Forks and/or Caster Assemblies Adjusting Anti-Dive SpringsRemoving/Installing the Joystick Assembly ElectronicsRemoving/Installing the Joystick Assembly Repositioning the JoystickConnecting the Joystick Disconnecting/Connecting the JoystickDisconnecting the Joystick Disconnecting/Connecting the Joystick Using the Proper Batteries BatteriesRemoving/Installing the Batteries Removing/Installing the Batteries Connecting/Disconnecting Battery Cables Connecting Battery CablesTerminal CapNOTE Handles on batteries removed for clarity Disconnecting Battery Cables Charging BatteriesBattery Charger Operation Battery Charger Operation Accessories Installing/Removing the Crutch/Cane HolderInstalling/Removing the Oxygen Holder Installing/Removing/Using the Walker Holder Installing/Removing the Walker HolderUsing the Walker Holder Installing/Removing/Using the Walker HolderPronto M41 with SureStep Global Limited Warranty Excluding Canada Canada Limited Warranty USA

1143206 specifications

The Invacare 1143206 is a highly regarded mobility product recognized for its robust design and advanced features, specifically tailored to enhance user comfort and mobility. This wheelchair is engineered with both user needs and caregiver requirements in mind, ensuring an optimal blend of functionality, durability, and ease of use.

One of the standout features of the Invacare 1143206 is its adjustable seating system. This innovative design allows users to customize the seating position according to their individual needs. The seat height can be adjusted easily, accommodating a variety of users and enhancing accessibility for those with different heights. The backrest is also adjustable, providing additional support for the user, which is essential for long-term comfort.

The wheelchair is constructed from high-quality materials to ensure longevity and reliability. The frame is made from sturdy steel, which not only supports the user effectively but also contributes to the overall stability of the chair. The innovative design minimizes the risk of tipping and enhances safety, particularly when navigating uneven surfaces.

Invacare has integrated several technologies to enhance the user experience, including advanced wheel and tire designs that offer superior grip and maneuverability. The footrests are swing-away and adjustable, allowing users to enter and exit the chair with ease.

Another important characteristic of the Invacare 1143206 is its lightweight structure. While the frame is sturdy, it is also designed to be easily transportable. This makes it ideal for users who may need to load it into vehicles or transport it for outings, as caregivers can do so without significant effort.

Safety is paramount in the engineering of the Invacare 1143206. The wheelchair features reliable brakes and locking mechanisms that allow for secure positioning during use. Additionally, the wheels are designed to prevent accidental rolling, making it a safe choice for both users and caregivers.

In summary, the Invacare 1143206 is a thoughtfully designed wheelchair that encompasses a range of essential features and technologies. Its adjustable seating system, lightweight structure, ergonomic design, and safety features collectively make it a preferred choice for users seeking comfort and mobility solutions. Whether for daily use or occasional outings, this wheelchair stands out as a dependable and versatile option.