Invacare 1143206 manual Installing/Removing the Oxygen Holder

Page 67

SECTION 14—ACCESSORIES

Installing/Removing the Oxygen Holder

WARNING

Contact your oxygen supplier for instructions in the use of oxygen. Extreme care MUST be exercised when using oxygen in close proximity to electric circuits.

The Invacare oxygen holder is designed to be used in conjunction with oxygen cylinder models MD15 and ME24 only.

To maintain safety, use only Invacare oxygen cylinder accessories (i.e. regulator, oxygen demand devices).

DO NOT use the oxygen holder for anything other than its intended purpose of supporting an oxygen cylinder - otherwise, injury or damage may occur.

DO NOT attempt to modify the oxygen holder to fit any other type of wheelchair. The oxygen holder was designed specifically for Invacare wheelchairs only.

The installation of the oxygen holder onto the back of the wheelchair seat significantly increases the length of the wheelchair. When turning the wheelchair it is important to take note of this increased length - otherwise, injury or damage may occur.

When using nasal or masked type administering equipment, oxygen or air tubing MUST be routed and secured properly to ensure that the tubing does not become entangled, kinked or severed. If necessary, loosen but DO NOT remove the mount- ing knob.

NOTE: For this procedure, refer to FIGURE 14.2 on page 68.

NOTE: Reverse the following procedure to remove the oxygen holder.

NOTE: The Crutch/Cane Holder, Oxygen Holder, and Walker Holder all install into the accessory tube. Only one of these may be installed at a time.

1.Install the mounting tube of the oxygen holder into the accessory tube located on the back of the seat.

2.Position the appropriate fastener into the welded nut on the accessory tube.

3.Grip the mounting hand knob firmly, and securely tighten it.

4.Thread the two clamp knobs through the two welded nuts on the upper support of the oxygen holder, and position the two protective caps on the end of the clamp knobs.

5.Repeat STEP 4 for the two clamp knobs on the lower support of the oxygen holder.

Part No. 1143206

67

Pronto® M41 with SureStep®

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Pronto M41 With SureStep Reference Documents Accessories WarningTable of Contents Arms Batteries Meaning Special NotesSpecial Notes Positive + Label LocationFOLD-DOWN Typical Product ParametersTypical Product Parameters FOLD-DOWN Operation Information Controller Settings/Repair or ServiceAccessories Information General GuidelinesGeneral Guidelines Charging Batteries BatteriesRain Test Weight TrainingWeight Limitation Grounding InstructionsEMI Information EMI Information Setup Checklist Initial SetupStability and Balance SAFETY/HANDLING of WheelchairsCoping With Everyday Obstacles Coping With Everyday ObstaclesLifting/Stairways Pinch PointsLifting/Stairways Transferring To and From Other Seats Transferring To and From Other SeatsReaching and Bending Backward Reaching, Leaning and Bending ForwardSafety Inspection Checklists Safety InspectionInspect/Adjust Initially Inspect/Adjust Monthly Inspect/Adjust WeeklyInspect/Adjust Periodically Troubleshooting GuideAll Wheelchairs SPJ+ Joysticks Troubleshooting ElectricalInformation Gauge Display Diagnostics Wheelchair Operation Turning the Power On/OffMovement Action Using the Joystick to Drive the WheelchairOn/Off Button MK5 SPJ-INT Joystick Switches and IndicatorsSpeedometer Joystick Speed Control ButtonsCharger/Programming Input Information Gauge Display Service IndicatorArms Removing/Installing the ArmsAdjusting Width Adjusting the ArmsAdjusting Angle Adjusting Depth Fold Down Back Seats Only Adjusting Height Semi-Recline Seats OnlyRemoving Removing/Installing the Seat AssemblyInstalling SeatAdjusting the Headrest Adjusting the Back Angle Semi-Recline BackBack seat shown Replacing the Seat Positioning StrapRemoving/Installing the Footboard Assembly Footboard AssemblyAngle Adjusting the Footboard AssemblyDepth Adjusting the Footboard Assembly DepthHeight Adjusting the Footboard Assembly HeightFront Riggings Installing/Removing Front RiggingsModel PHWH93 Adjusting Footrest HeightModel PH904A and PHAL4A Replacing Heel LoopsRaising/Lowering Elevating Front Riggings Adjusting/Replacing Telescoping Front Rigging SupportsFront Rigging Shroud and Wheels Removing/Installing the Top ShroudReplacing the Flat Free Tires on the Wheel Rim Removing/Installing the Rear Shroud Engaging/Disengaging Motor Release Lever Removing/Installing CastersRemoving/Installing Casters Adjusting ForksAdjusting Anti-Dive Springs Removing/Installing Forks and/or Caster AssembliesElectronics Removing/Installing the Joystick AssemblyRepositioning the Joystick Removing/Installing the Joystick AssemblyDisconnecting the Joystick Disconnecting/Connecting the JoystickConnecting the Joystick Disconnecting/Connecting the Joystick Batteries Using the Proper BatteriesRemoving/Installing the Batteries Removing/Installing the Batteries Connecting Battery Cables Connecting/Disconnecting Battery CablesTerminal CapNOTE Handles on batteries removed for clarity Charging Batteries Disconnecting Battery CablesBattery Charger Operation Battery Charger Operation Installing/Removing the Crutch/Cane Holder AccessoriesInstalling/Removing the Oxygen Holder Installing/Removing the Walker Holder Installing/Removing/Using the Walker HolderInstalling/Removing/Using the Walker Holder Using the Walker HolderPronto M41 with SureStep Global Limited Warranty Excluding Canada USA Canada Limited Warranty

1143206 specifications

The Invacare 1143206 is a highly regarded mobility product recognized for its robust design and advanced features, specifically tailored to enhance user comfort and mobility. This wheelchair is engineered with both user needs and caregiver requirements in mind, ensuring an optimal blend of functionality, durability, and ease of use.

One of the standout features of the Invacare 1143206 is its adjustable seating system. This innovative design allows users to customize the seating position according to their individual needs. The seat height can be adjusted easily, accommodating a variety of users and enhancing accessibility for those with different heights. The backrest is also adjustable, providing additional support for the user, which is essential for long-term comfort.

The wheelchair is constructed from high-quality materials to ensure longevity and reliability. The frame is made from sturdy steel, which not only supports the user effectively but also contributes to the overall stability of the chair. The innovative design minimizes the risk of tipping and enhances safety, particularly when navigating uneven surfaces.

Invacare has integrated several technologies to enhance the user experience, including advanced wheel and tire designs that offer superior grip and maneuverability. The footrests are swing-away and adjustable, allowing users to enter and exit the chair with ease.

Another important characteristic of the Invacare 1143206 is its lightweight structure. While the frame is sturdy, it is also designed to be easily transportable. This makes it ideal for users who may need to load it into vehicles or transport it for outings, as caregivers can do so without significant effort.

Safety is paramount in the engineering of the Invacare 1143206. The wheelchair features reliable brakes and locking mechanisms that allow for secure positioning during use. Additionally, the wheels are designed to prevent accidental rolling, making it a safe choice for both users and caregivers.

In summary, the Invacare 1143206 is a thoughtfully designed wheelchair that encompasses a range of essential features and technologies. Its adjustable seating system, lightweight structure, ergonomic design, and safety features collectively make it a preferred choice for users seeking comfort and mobility solutions. Whether for daily use or occasional outings, this wheelchair stands out as a dependable and versatile option.
Top Page Image Contents