Multiquip FCG1-6HA manual Blade Placement, Diamond Blades, Blade Speed, Cutting Depth

Page 20

BLADE PLACEMENT

Table 4. Material Listing And Blade Selection

Material

Blade

 

 

Cured Concrete

Cured Concrete Blade

 

 

Green Concrete

Green Concrete Blade

 

 

Asphalt

Asphalt Blade

 

 

Asphalt over Concrete

Asphalt/Concrete Blade

 

 

Block, Brick, Masonry, Refractories

Masonry Blade

 

 

Tile, Ceramic, Stone

Tile Blade

 

 

Diamond Blades

Selecting the diamond blade TYPE and GRADE defines how the blade will perform both in cutting speed and blade life.

Selection of the proper diamond blade consists of:

Material to be Cut

Type of Saw Being Used

Spindle Speed of Saw

Hardness Characteristics of the Material

Performance Expectations

Factors for sawing economy:

Type of Blade

Depth of Cut

Sawing Speed

Characteristics of the Material Being Cut

Blade Speed

A diamond blade’s performance is directly connected to specific peripheral (rim) speeds.

The following shaft rotational speeds have been factory set to ensure optimum blade performance.

FCG16HA - 10” (254 mm)Capacity - 6000 RPM.

WARNING

Operating saw blades at rotational speeds greater than those specified by the manufac- turer can cause blade damage, and may in- jure the user or others in the operating area.

Cutting Depth

The FCG16HA Concrete Saw has a capacity for a 10" blade with an 0.675" (15.9 mm) Arbor diameter. This allows a cutting range from 0" to 3 1/4".

BLADE PLACEMENT

WARNING

Failure to thoroughly inspect the diamond blade for operational safety could result in damage to the blades or the saw and may cause injury to the user or others in the operating area.

Refer to Figure 12 for the following components.

1.Blade Guard - Pivot the blade guard front cover all the way back. The guard tension spring will keep the front cover in position.

2.Blade Hex Nut - Unscrew the blade shaft nut (right side loosens clockwise and tightens counter-clockwise while the left side loosens counter-clockwise and tightens clockwise. DO NOT overtighten the nut (approximately 45-50 ft. lb/61- 68 N/m) when finalizing the assembly.

3.Outside Blade Flange (Collar) - Ensure that the outside blade flange is placed flush against the diamond blade. The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade core.

PAGE 20 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)

Image 20
Contents Model FCG1-6HA Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents FCG16HA SlabSaver Concrete SawSpecifications FCG1 Concrete Saw SpecificationsDimensions SideView Front ViewSafety Message Alert Symbols Foryour Safety and the Safety of Others8 FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Rules for Safe Operation Rules for Safe OperationGeneral Safety Diamond Blade SafetyEmergencies Maintenance SafetySaw Transportation Safety General Information Intended UseFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Components FCG16HA Concrete SawBeltTension Adjuster Adjusts belt tension Basic Engine Engine Controls and ComponentsGUARDS, Covers and V-BELTS National Standards Institute Ansi B7.1 and B7.5Belt Check Belt Alignment and TensioningTo Tighten the V-belt To Remove and Replace the V-beltBlades Diamond BladeBlade Placement Diamond BladesBlade Speed Cutting DepthBlade Removal and Replacement Diamond Blade PlacementCutting Depth Adjustment Raise/Lower AssemblyInspection Before StartingEngine Oil Check Blade CheckEngine Shutdown Switch OperationThrottle Lever Stopping the Engine Rotate the throttle lever toward full throttleRestarting After Intervention Maintenance Engine tank & strainer Fuel lineSpark plug Chassis LubricationTroubleshooting SAW Blade TroubleshootingTroubleshooting Engine Troubleshooting EngineTroubleshooting Engine FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts To 3 UnitsDecal Locator Decal LocatorPart Name Guards Assy Part Name QTY Remarks Guides Assy SCREW, HHC 3/8 16 X 3 Full Thrd Undercarriage Assy Part Name QTY Handle & Depth Adjuster Assy Frame Engine & Blade Drive Assy WASHER, Lock 5/16 MED Honda GX200QXC9 AIR Cleaner Cyclone Assy GASKET, Elbow Honda GX200QXC9 Camshaft Assy ROD, Push Honda GX200QXC9 Carburetor Assy Gasket SET Honda GX200QXC9 Control Assy ARM, Governor Honda GX200QXC9 Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX200QXC9 Crankshaft Assy Crankshaft Q- Type Honda GX200QXC9 Cylinder Barrel Assy Switch ASSEMBLY, OIL Level Honda GX200QXC9 Cylinder Head Assy CLIP, Valve Guide Honda GX200QXC9 FAN Cover Assy COVER, FAN *R8* Bright RED Honda GX200QXC9 Flywheel Assy FAN, Cooling Honda GX200QXC9 Fuel Tank Assy RUBBER, Supporter 107MM Honda GX200QXC9 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX200QXC9 Muffler Assy Muffler Honda GX200QXC9 Piston Assy Ring SET, Piston Standard Honda GX200QXC9 Recoil Starter Assy R8* Bright RED No Illustration Available Honda GX200QXC9 Gasket KIT AssyGASKET, Case Cover Honda GX200QXC9 Labels Assy Emblem Terms and Conditions of Sale Parts Freight PolicyFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 HERE’S HOW to GET Help

FCG1-6HA specifications

The Multiquip FCG1-6HA is an advanced compact generator designed to meet the needs of contractors, event planners, and outdoor enthusiasts. This generator is known for its reliability, efficiency, and user-friendly features that make it an essential tool in various applications.

One of the standout features of the FCG1-6HA is its powerful Honda engine, which delivers robust performance while ensuring fuel efficiency. The engine operates quietly, making it ideal for noise-sensitive environments such as residential areas and outdoor events. With a strong output capacity, the generator provides a stable power supply for multiple devices and tools simultaneously.

The FCG1-6HA is equipped with advanced inverter technology, which produces clean and stable electricity. This feature is particularly important for sensitive electronics like laptops, smartphones, and medical equipment, ensuring they operate safely without the risk of damage from unstable power.

The generator's compact and lightweight design enhances its portability, allowing users to transport it easily to remote job sites or recreational areas. The durable frame construction ensures it can withstand tough conditions, making it an excellent choice for construction sites and outdoor adventures.

Another significant characteristic of the FCG1-6HA is its user-friendly control panel. The intuitive layout with easy-to-read indicators and straightforward controls simplifies operation for users of all experience levels. Additionally, it features multiple outlets, including 120V and 12V options, providing versatility for various power requirements.

Safety is also a priority in the design of the FCG1-6HA. It includes built-in protective features such as an overload protection system, which automatically shuts down the generator in the event of excessive load, preventing damage. The unit also has a fuel shutoff feature to minimize the risk of spillage and leaks, ensuring safer operation.

The efficiency and low emissions of the FCG1-6HA align with modern environmental standards, making it a responsible choice for users conscious of their ecological footprint.

In summary, the Multiquip FCG1-6HA stands out as a powerful, efficient, and portable generator. Its reliable Honda engine, inverter technology, lightweight design, and robust safety features make it an ideal solution for anyone needing dependable power in a variety of settings. Whether for work or leisure, this generator delivers performance without compromise.