Multiquip FCG1-6HA manual Troubleshooting SAW, Blade Troubleshooting

Page 30

 

 

TROUBLESHOOTING (SAW)

 

 

 

 

TABLE 6. BLADE TROUBLESHOOTING

 

 

 

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

 

 

 

 

Blade too hard for the material being

Consult Dealer or Multiquip for correct blade. Try cutting

 

very soft material (sandstone, silica brick, cinder block) to

 

cut?

 

"Redress" the blade.

 

 

 

 

 

 

Engine torque diminished because of

Tighten and/or replace V-Belt.

 

loose V-belt?

 

 

Blade slows or stops cutting,

 

 

 

 

still remains on blade

Insufficient Engine power?

Check throttle setting. Check Engine horsepower.

 

 

 

 

Improper dircection of rotation?

Check that the blade is properly oriented and rotational

 

arrow points in a "Down-Cutting" direction.

 

 

 

 

 

 

Blade is slipping on the blade shaft?

Check that the blade & flange pin are properly installed on

 

the blade shaft.

 

 

 

 

 

 

Blade being used on misaligned saw?

Check blade shaft bearings and alignment integrity.

 

 

 

 

Blade is excessively hard for the

Check specification of the blade with the material being

 

material being cut?

cut. Consult Dealer or Multiquip for information.

 

 

 

Blade does not cut straight

Blade being used at improper RPM?

Ensure blade surface feet per minute speed (SFPM) is

approximately 6,000.

and/or true.

 

 

 

 

Blade improperly mounted on arbor

Ensure blade is properly affixed on the blade shaft.

 

shoulders and flanges?

 

 

 

 

 

 

Excessive force applied to blade while

DO NOT force the blade in the cut. Apply a slow and

 

cutting?

steady pace when sawing.

 

 

 

 

Blades too hard for the material being

Consult Dealer or Multiquip for correct blade. Try cutting

 

very soft material (sandstone, silica brick, cinder block) to

 

cut?

 

"Redress" the blade.

 

 

 

 

 

 

Blade improperly mounted on arbor

Ensure blade is properly affixed on the blade shaft.

 

shoulders and flanges??

 

 

 

 

 

 

 

Ensure proper flow & volume of water is provided for wet

Blade discoloring, crackling

Blade not receiving enough cooling air?

cutting blades. Ensure sufficient cooling air is circulated

 

about a dry cutting blade.

and/or wearing excessively.

 

 

 

 

Arbor hole out of round?

Ensure blade is properly affixed on the blade shaft.

 

 

 

 

Incorrect blade chosen for material

Check specification of the blade with the material being

 

being cut?

cut. Consult Dealer or Multiquip for information.

 

 

 

 

Excessive force applied to blade while

DO NOT force the blade in the cut. Apply a slow and

 

cutting?

steady pace when sawing.

 

 

 

PAGE 30 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Model FCG1-6HA Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents FCG16HA SlabSaver Concrete SawSpecifications FCG1 Concrete Saw SpecificationsDimensions SideView Front ViewSafety Message Alert Symbols Foryour Safety and the Safety of Others8 FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Rules for Safe Operation Rules for Safe OperationGeneral Safety Diamond Blade SafetyMaintenance Safety Saw Transportation SafetyEmergencies General Information Intended UseFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Components FCG16HA Concrete SawBeltTension Adjuster Adjusts belt tension Basic Engine Engine Controls and ComponentsBelt Check GUARDS, Covers and V-BELTSNational Standards Institute Ansi B7.1 and B7.5 Belt Alignment and TensioningTo Tighten the V-belt To Remove and Replace the V-beltBlades Diamond BladeBlade Speed Blade PlacementDiamond Blades Cutting DepthBlade Removal and Replacement Diamond Blade PlacementCutting Depth Adjustment Raise/Lower AssemblyEngine Oil Check InspectionBefore Starting Blade CheckEngine Shutdown Switch OperationThrottle Lever Stopping the Engine Rotate the throttle lever toward full throttle Restarting After Intervention Maintenance Spark plug Engine tank & strainerFuel line Chassis LubricationTroubleshooting SAW Blade TroubleshootingTroubleshooting Engine Troubleshooting EngineTroubleshooting Engine FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts To 3 UnitsDecal Locator Decal LocatorPart Name Guards Assy Part Name QTY Remarks Guides Assy SCREW, HHC 3/8 16 X 3 Full Thrd Undercarriage Assy Part Name QTY Handle & Depth Adjuster Assy Frame Engine & Blade Drive Assy WASHER, Lock 5/16 MED Honda GX200QXC9 AIR Cleaner Cyclone Assy GASKET, Elbow Honda GX200QXC9 Camshaft Assy ROD, Push Honda GX200QXC9 Carburetor Assy Gasket SET Honda GX200QXC9 Control Assy ARM, Governor Honda GX200QXC9 Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX200QXC9 Crankshaft Assy Crankshaft Q- Type Honda GX200QXC9 Cylinder Barrel Assy Switch ASSEMBLY, OIL Level Honda GX200QXC9 Cylinder Head Assy CLIP, Valve Guide Honda GX200QXC9 FAN Cover Assy COVER, FAN *R8* Bright RED Honda GX200QXC9 Flywheel Assy FAN, Cooling Honda GX200QXC9 Fuel Tank Assy RUBBER, Supporter 107MM Honda GX200QXC9 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX200QXC9 Muffler Assy Muffler Honda GX200QXC9 Piston Assy Ring SET, Piston Standard Honda GX200QXC9 Recoil Starter Assy R8* Bright RED No Illustration Available Honda GX200QXC9 Gasket KIT AssyGASKET, Case Cover Honda GX200QXC9 Labels Assy Emblem Terms and Conditions of Sale Parts Freight PolicyFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 HERE’S HOW to GET Help
Top Page Image Contents