Multiquip FCG1-6HA manual Blade Removal and Replacement, Diamond Blade Placement

Page 21

BLADE PLACEMENT

4.Diamond Blade - Ensure that the proper diamond blade has been selected for the job. Pay close attention to the directional arrows on the blade. The blade's operating directional arrows must point in a "down-cutting" direction to perform correctly. When placing the blade onto the blade shaft, ensure the arbor hole of the blade matches the diameter of the shaft.

WARNING

Dropping or forcing the blade onto the cutting surface can severely damage the diamond blade and may cause serious damage to the saw and bodily harm.

Blade Removal and Replacement

1.Ensure the Engine Shutdown switch (Item 22, Fig.3) and the ON/OFF switch on the engine are turned to the "OFF" position.

2.Place the FCG16HA Saw on a stable level working surface.

3.Ensure the blade is raised and the raise/lower rod is locked into position.

4.Raise the blade by appling a downward pressure on the handlebars to raise the blade and allow the raise/lower rod to drop into the "raised-position" slot.

Figure 12. Diamond Blade Placement

5.Inner Flange (Collar) - This flange is fixed upon the blade shaft. The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade.

The following steps should be accomplished before using the FCG16HA Saw on any cutting surface.

When removing or installing a diamond blade, please note that the blade retaining nuts are left and right-hand threaded.

5.Lift up the blade guard cover (item 1 Figure 12) to gain access to the diamond blade.

6.Use the provided blade nut and blade shaft locking wrenches (Figure 12) to install the diamond blade.

7.While holding the blade shaft with the locking wrench, remove the blade hex nut (clockwise direction) and outer blade flange.

8.Remove the old blade and install a new blade in the same rotational direction as marked on the blade.

9.Reinstall the outer blade flange and hex nut. Tighten the nut firmly (counter-clockwise direction). DO NOT OVER

TIGHTEN.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model FCG1-6HA Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningFCG16HA SlabSaver Concrete Saw Table of ContentsFCG1 Concrete Saw Specifications SpecificationsSideView Front View DimensionsForyour Safety and the Safety of Others Safety Message Alert Symbols8 FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Rules for Safe Operation Rules for Safe OperationDiamond Blade Safety General SafetyMaintenance Safety Saw Transportation SafetyEmergencies Intended Use General InformationFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 FCG16HA Concrete Saw ComponentsBeltTension Adjuster Adjusts belt tension Engine Controls and Components Basic EngineNational Standards Institute Ansi B7.1 and B7.5 GUARDS, Covers and V-BELTSBelt Check Belt Alignment and TensioningTo Remove and Replace the V-belt To Tighten the V-beltDiamond Blade BladesDiamond Blades Blade PlacementBlade Speed Cutting DepthDiamond Blade Placement Blade Removal and ReplacementRaise/Lower Assembly Cutting Depth AdjustmentBefore Starting InspectionEngine Oil Check Blade CheckOperation Engine Shutdown SwitchThrottle Lever Rotate the throttle lever toward full throttle Stopping the EngineRestarting After Intervention Maintenance Fuel line Engine tank & strainerSpark plug Chassis LubricationBlade Troubleshooting Troubleshooting SAWTroubleshooting Engine Troubleshooting EngineTroubleshooting Engine FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Explanation of Code in Remarks Column Sample Parts ListTo 3 Units Suggested Spare PartsDecal Locator Decal LocatorPart Name Guards Assy Part Name QTY Remarks Guides Assy SCREW, HHC 3/8 16 X 3 Full Thrd Undercarriage Assy Part Name QTY Handle & Depth Adjuster Assy Frame Engine & Blade Drive Assy WASHER, Lock 5/16 MED Honda GX200QXC9 AIR Cleaner Cyclone Assy GASKET, Elbow Honda GX200QXC9 Camshaft Assy ROD, Push Honda GX200QXC9 Carburetor Assy Gasket SET Honda GX200QXC9 Control Assy ARM, Governor Honda GX200QXC9 Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX200QXC9 Crankshaft Assy Crankshaft Q- Type Honda GX200QXC9 Cylinder Barrel Assy Switch ASSEMBLY, OIL Level Honda GX200QXC9 Cylinder Head Assy CLIP, Valve Guide Honda GX200QXC9 FAN Cover Assy COVER, FAN *R8* Bright RED Honda GX200QXC9 Flywheel Assy FAN, Cooling Honda GX200QXC9 Fuel Tank Assy RUBBER, Supporter 107MM Honda GX200QXC9 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX200QXC9 Muffler Assy Muffler Honda GX200QXC9 Piston Assy Ring SET, Piston Standard Honda GX200QXC9 Recoil Starter Assy R8* Bright RED Honda GX200QXC9 Gasket KIT Assy No Illustration AvailableGASKET, Case Cover Honda GX200QXC9 Labels Assy Emblem Freight Policy Terms and Conditions of Sale PartsFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 HERE’S HOW to GET Help

FCG1-6HA specifications

The Multiquip FCG1-6HA is an advanced compact generator designed to meet the needs of contractors, event planners, and outdoor enthusiasts. This generator is known for its reliability, efficiency, and user-friendly features that make it an essential tool in various applications.

One of the standout features of the FCG1-6HA is its powerful Honda engine, which delivers robust performance while ensuring fuel efficiency. The engine operates quietly, making it ideal for noise-sensitive environments such as residential areas and outdoor events. With a strong output capacity, the generator provides a stable power supply for multiple devices and tools simultaneously.

The FCG1-6HA is equipped with advanced inverter technology, which produces clean and stable electricity. This feature is particularly important for sensitive electronics like laptops, smartphones, and medical equipment, ensuring they operate safely without the risk of damage from unstable power.

The generator's compact and lightweight design enhances its portability, allowing users to transport it easily to remote job sites or recreational areas. The durable frame construction ensures it can withstand tough conditions, making it an excellent choice for construction sites and outdoor adventures.

Another significant characteristic of the FCG1-6HA is its user-friendly control panel. The intuitive layout with easy-to-read indicators and straightforward controls simplifies operation for users of all experience levels. Additionally, it features multiple outlets, including 120V and 12V options, providing versatility for various power requirements.

Safety is also a priority in the design of the FCG1-6HA. It includes built-in protective features such as an overload protection system, which automatically shuts down the generator in the event of excessive load, preventing damage. The unit also has a fuel shutoff feature to minimize the risk of spillage and leaks, ensuring safer operation.

The efficiency and low emissions of the FCG1-6HA align with modern environmental standards, making it a responsible choice for users conscious of their ecological footprint.

In summary, the Multiquip FCG1-6HA stands out as a powerful, efficient, and portable generator. Its reliable Honda engine, inverter technology, lightweight design, and robust safety features make it an ideal solution for anyone needing dependable power in a variety of settings. Whether for work or leisure, this generator delivers performance without compromise.
Top Page Image Contents