Multiquip FCG1-6HA manual Stopping the Engine, Rotate the throttle lever toward full throttle

Page 26

OPERATION

7.If the engine has started, slowly return the choke lever (Figure 20) to the "OPEN" position. If the engine has not started repeat steps 1 through 5.

8.Before the saw is placed into operation, run the engine for several minutes. Check for fuel leaks, and noises that would associate with a loose guards and/or covers.

9.Rotate the throttle lever (Figure 21) toward full throttle.

WARNING

ALWAYS cut with the saw at FULLTHROTTLE. Attempting to cut with the saw at less than full throttle could cause the blade to bind or stop abruptly in the slab resulting in serious injury to the operator or others in the area.

Stopping the Engine

Stopping the engine under normal conditions:

1.Place the engine throttle lever (Figure 23) in the SLOW

position, and listen for the engine speed to decrease. Allow engine to run for 2 or 3 minutes for proper cooldown.

Figure 23. Throttle Lever

2.Turn the engine Shutdown switch (next to the handle lock)

(Figure 24) to the "OFF" position. Shutting the engine off using this switch confirms that is is functioning properly.

 

WARNING

 

 

 

ALWAYS keep clear of rotating or moving parts while

 

 

operating this equipment.

 

 

 

 

 

 

Figure 24. Engine Shutdown Switch

10. To begin sawing, lower the rotating blade allowing it to cut to

 

the preset depth.

3. Turn the engine ON/OFF switch (Figure 25) to the "OFF"

 

 

 

 

11. When blade has reached full cutting depth, slowly walk

position.

 

behind the saw at a rate that will allow the engine to operate

 

without losing optimum RPM.

 

 

 

 

 

CAUTION

 

 

 

DO NOT try to cut faster than the blade will allow. Cutting

 

 

too fast will cause the blade to rise up out of the cut.

 

 

Improper cutting rate can decrease the life of the engine

 

Figure 25. Engine ON/Off Switch ( engine)

and blades.

 

 

 

 

 

 

4. Place the fuel valve lever (Figure 26) to the OFF position.

12. When the end of the cut has been reached, raise the blade

 

out of the cut by pulling back on the handlebars (using a

 

downward pressure) until the raise/lower rod drops into its

 

slot with the blade in the raised position.

 

13. If cutting is complete, shut the saw down using the following

 

"ShutdownProcedures".

 

 

 

 

 

Figure 26. Fuel Valve Lever (Off Position)

PAGE 26 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)

Image 26
Contents Model FCG1-6HA Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents FCG16HA SlabSaver Concrete SawSpecifications FCG1 Concrete Saw SpecificationsDimensions SideView Front ViewSafety Message Alert Symbols Foryour Safety and the Safety of Others8 FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Rules for Safe Operation Rules for Safe OperationGeneral Safety Diamond Blade SafetyEmergencies Maintenance SafetySaw Transportation Safety General Information Intended UseFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Components FCG16HA Concrete SawBeltTension Adjuster Adjusts belt tension Basic Engine Engine Controls and ComponentsBelt Check GUARDS, Covers and V-BELTSNational Standards Institute Ansi B7.1 and B7.5 Belt Alignment and TensioningTo Tighten the V-belt To Remove and Replace the V-beltBlades Diamond BladeBlade Speed Blade PlacementDiamond Blades Cutting DepthBlade Removal and Replacement Diamond Blade PlacementCutting Depth Adjustment Raise/Lower AssemblyEngine Oil Check InspectionBefore Starting Blade CheckEngine Shutdown Switch OperationThrottle Lever Stopping the Engine Rotate the throttle lever toward full throttleRestarting After Intervention Maintenance Spark plug Engine tank & strainerFuel line Chassis LubricationTroubleshooting SAW Blade TroubleshootingTroubleshooting Engine Troubleshooting EngineTroubleshooting Engine FCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts To 3 UnitsDecal Locator Decal LocatorPart Name Guards Assy Part Name QTY Remarks Guides Assy SCREW, HHC 3/8 16 X 3 Full Thrd Undercarriage Assy Part Name QTY Handle & Depth Adjuster Assy Frame Engine & Blade Drive Assy WASHER, Lock 5/16 MED Honda GX200QXC9 AIR Cleaner Cyclone Assy GASKET, Elbow Honda GX200QXC9 Camshaft Assy ROD, Push Honda GX200QXC9 Carburetor Assy Gasket SET Honda GX200QXC9 Control Assy ARM, Governor Honda GX200QXC9 Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX200QXC9 Crankshaft Assy Crankshaft Q- Type Honda GX200QXC9 Cylinder Barrel Assy Switch ASSEMBLY, OIL Level Honda GX200QXC9 Cylinder Head Assy CLIP, Valve Guide Honda GX200QXC9 FAN Cover Assy COVER, FAN *R8* Bright RED Honda GX200QXC9 Flywheel Assy FAN, Cooling Honda GX200QXC9 Fuel Tank Assy RUBBER, Supporter 107MM Honda GX200QXC9 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX200QXC9 Muffler Assy Muffler Honda GX200QXC9 Piston Assy Ring SET, Piston Standard Honda GX200QXC9 Recoil Starter Assy R8* Bright RED No Illustration Available Honda GX200QXC9 Gasket KIT AssyGASKET, Case Cover Honda GX200QXC9 Labels Assy Emblem Terms and Conditions of Sale Parts Freight PolicyFCG16HA SAW Operation and Parts Manual REV. #1 03/19/10 HERE’S HOW to GET Help

FCG1-6HA specifications

The Multiquip FCG1-6HA is an advanced compact generator designed to meet the needs of contractors, event planners, and outdoor enthusiasts. This generator is known for its reliability, efficiency, and user-friendly features that make it an essential tool in various applications.

One of the standout features of the FCG1-6HA is its powerful Honda engine, which delivers robust performance while ensuring fuel efficiency. The engine operates quietly, making it ideal for noise-sensitive environments such as residential areas and outdoor events. With a strong output capacity, the generator provides a stable power supply for multiple devices and tools simultaneously.

The FCG1-6HA is equipped with advanced inverter technology, which produces clean and stable electricity. This feature is particularly important for sensitive electronics like laptops, smartphones, and medical equipment, ensuring they operate safely without the risk of damage from unstable power.

The generator's compact and lightweight design enhances its portability, allowing users to transport it easily to remote job sites or recreational areas. The durable frame construction ensures it can withstand tough conditions, making it an excellent choice for construction sites and outdoor adventures.

Another significant characteristic of the FCG1-6HA is its user-friendly control panel. The intuitive layout with easy-to-read indicators and straightforward controls simplifies operation for users of all experience levels. Additionally, it features multiple outlets, including 120V and 12V options, providing versatility for various power requirements.

Safety is also a priority in the design of the FCG1-6HA. It includes built-in protective features such as an overload protection system, which automatically shuts down the generator in the event of excessive load, preventing damage. The unit also has a fuel shutoff feature to minimize the risk of spillage and leaks, ensuring safer operation.

The efficiency and low emissions of the FCG1-6HA align with modern environmental standards, making it a responsible choice for users conscious of their ecological footprint.

In summary, the Multiquip FCG1-6HA stands out as a powerful, efficient, and portable generator. Its reliable Honda engine, inverter technology, lightweight design, and robust safety features make it an ideal solution for anyone needing dependable power in a variety of settings. Whether for work or leisure, this generator delivers performance without compromise.