Fluke ESA612 Connecting to Line Power Turning the Analyzer On, Connecting a DUT to the Analyzer

Page 22

ESA612

Users Manual

Connecting to Line Power	Turning the Analyzer On
XWWarning	Note

To avoid shock hazard and for proper Analyzer operation, connect the factory supplied three-conductor line power cord to a properly grounded power outlet. Do not use a two-conductor adapter or extension cord; this will break the protective ground connection.

Connect the Analyzer to a properly grounded three-prong outlet. The Analyzer will not properly test a DUT when the ground lead is open.

The Analyzer is intended for use with single-phase, grounded power. It is not intended for dual, split-phase or three-phase power configurations. But it can be used with any power system that supplies the correct voltages for single-phase and is grounded, or is an isolated power system.

Connecting a DUT to the Analyzer

A Device Under Test (DUT) can be connected in a number of different ways depending on the device and the number of connections needed for a full electrical safety test. Figure 4 shows a DUT connected to the test receptacle, applied parts posts, and a separate connection to the DUT’s enclosure or protective earth ground.

To ensure the high voltage indicator is working, look for it to illuminate during the power-up self test.

Press the power switch on the left-side panel so the “I” side of the ac power switch is depressed. The Analyzer will perform a series of self tests and then display the message shown in Figure 3 when the self test has completed successfully.

fis101.jpg

Figure 3. Analyzer Ready for Operation

8

Image 22

Contents ESA612 Warranty and Product Support Contents Standard Terms and Conditions Certification Restrictions and Liabilities Table of Contents ESA612 Iii ESA612 List of Tables ESA612 List of Figures Viii Electrical Safety Analyzer IntroductionSafety Information Symbol DescriptionElectrical Safety Analyzer Intended UseUnpacking the Analyzer Instrument FamiliarizationInstrument Familiarization Side and Top-Panel Connections Side and Top-Panel Connections Name Connecting to Line Power Turning the Analyzer On Connecting a DUT to the AnalyzerTurning the Analyzer On Accessing the Analyzer’s Functions Leakage Current MenuSetting Polarity Switching Delay Setting Up the AnalyzerSetting the Display Contrast Setting up the Beeper Performing Electrical Safety TestsSetting the Gfci Limit Viewing MemoryPerforming Mains Voltage Testing Setting the Test StandardPerforming a Ground Wire Protective Earth Resistance Test DUT is powered off for this test Electrical Safety Analyzer Fis112.eps Schematic Abbreviations Device Under Test Performing an Insulation Resistance Test Insulation Resistance MeasurementFaw17.eps Applied Parts to Protective-Earth Insulation Test Schematic Mains to Applied Parts Insulation Test Schematic Mains to Non-Earth Accessible Conductive Points Schematic Applied Parts to Non-Earth Conductive Points Schematic Performing a Current Consumption Test Performing Leakage Current TestsMeasuring Earth Leakage Current Electrical Safety Analyzer Earth Leakage Current Test Schematic Performing a Chassis Enclosure Leakage Test Enclosure Leakage Current Test Schematic Performing a Lead-to-Ground Patient Leakage Lead-to-Ground Patient Leakage Current Test Schematic Electrical Safety Analyzer TestsFaw30.eps Electrical Safety Analyzer Lead Isolation Mains On Applied Parts Leakage Test Schematic Test Performing Electrical Safety TestsPerforming an Alternative Equipment Leakage Performing an Alternative Applied Part Leakage TestAlternative Equipment Leakage Current Test Schematic Performing a Direct Equipment Leakage Test Alternative Applied Part Leakage Test Schematic When the EN62353 standard is selected Performing a Direct Applied Part Leakage TestDirect Equipment Leakage Test Schematic Direct Applied Parts Leakage Current Test Schematic Performing a Differential Leakage Current Test Differential Leakage Current Test Schematic Using the 1210 Adapter Using the 1210 Adapter ESA612 EGC Lead Connection with 1210 Adapter Measuring Resistance Making Point-To-Point MeasurementsMeasuring Voltage Simulating ECG Waveforms Measuring CurrentESA612 ECG Monitor Connections Using Memory Storing Data into MemoryViewing Memory Data Controlling the Analyzer RemotelyDeleting Data from Memory Maintenance Testing and Replacing the FusesCleaning the Analyzer Cleaning the AnalyzerReplaceable Parts Replaceable Parts Fluke Biomedical Part NumberReplaceable Parts Accessories Specifications TemperatureDetailed Specifications VoltageDetailed Specifications ECG Performance Waveforms