Toshiba DKT2104-CT manual Digital Technology, Handset

Page 14

The Grand Tour

Digital Technology

Digital Technology

The DKT2104-CT uses 900 MHz Digital Narrow Band technology that provides:

♦Unsurpassed range, two to three times greater than conventional analog cordless telephones.

♦Clarity that is so good, it is indistinguishable from corded telephones in most environments.

♦Maximum security for up to 30 cordless digital telephones that is almost impossible to scan.

Handset

Your cordless handset has special function buttons (shown at right) and an LCD that shows operating conditions.

The LCD displays “talk” when the battery is hot swapped (quickly removed and returned to the handset while talking). “Message” displays in standby mode only.

There is a ringer on the side of the handset that toggles the ringer/vibrator On and Off.

Table 1 describes the available buttons and Table 2 describes the LCD messages.

Note Though highly unlikely, it is possible for two cordless telephones to share the same channel. If this occurs, the DKT2104-CT will automatically switch to a clear channel within five seconds.

CD

alk	talk	chan	vol
alk	talk	chan
han
OLD
SG	1	2abc	3 def
	1	2abc	3 def
	4 ghi	5 jkl	6 mno
	7pqrs	8 tuv	9 wxyz
		0 oper	#

4483

vol

[DNs]

MUTE CNF/TRN

2	Strata DKT2104-CT Cordless Digital Telephone 5/00

Image 14

Contents DKT2104-CT Cordless Digital Telephone User Guide Digital Business Telephone SystemsPublication Information Contents Chapter Configuration Chapter Handset OperationFeatures IiiDo Not Disturb Appendix Contents Introduction Viii OrganizationConventions Action/Response Table See FigureRelated Documents and Media Grand Tour Digital Technology HandsetFkdq Base Unit Charger UnitVolume Levels BatteriesHandset Mute Battery Cordless Digital Telephone Standard PartsDesk Cordless Installation Review Safety InstructionsInstallation Strata DKT2104-CT Cordless Digital Telephone 5/00 Select Location Mount on a WallSnap the Base Unit onto the plate shown above To connect to a Strata DKT Connect Telephone CablesTo connect as a stand-alone telephone Charger Unit Connect and Apply PowerBase Unit Install Handset Battery Raise the Base Unit AntennaCharge Batteries for First Time Install Headset Optional Install Belt Clip To remove the belt clipInstallation Configuration3 Enter the Program Mode While holding and , press Wdon shown at right Press to toggle the settings for each program step Handset Operation To set the cordless mode $3512To change the signaling Tone or Voice First SignalingTo set DKT mode To answer a Tone First Signaling callRinger Volume Controlling Ringer and Handset VolumeHandset Volume Mute Your ConversationDial a DN Making CallsMaking Calls Internal NumbersExternal Numbers Answering Calls Recall/Override Busy StationsAny Console Using CO Line Access CodesCalling the Attendant Console Specific ConsoleUsing Isdn Trunks Transferring Calls Active CallsAnswering Transferred Call Transfer Calls to the CordlessUsing Camp-on Transfer Calls to the DKTConferencing Calls Add a Second LineAdd a Station Handset Operation Features Emergency Override of Forced Account Codes Account CodesForced Account Codes Voluntary Account Codes Verified Account CodesAutomatic Busy Redial Alarm ResetAlert Signaling Automatic CallbackLine Queuing Set Line QueuingAuto Redial Call ForwardCall Forward-All Calls Call Forward-BusyCall Forward-No Answer To set CF-No AnswerCall Forward-Cancel Call Forward-Busy/No AnswerCall Forward-External Set CF-ExternalCall Park Orbits Release 3 or Later Cancel CF-ExternalCall Forward-Fixed Retrieving Parked Calls Call ParkCO Line Pickup Call PickupDirected Call Pickup Group PickupCall Waiting Direct Station Selection Buttons HotlineDo Not Disturb Door UnlockAnswering Calls at Other Stations Door TelephoneAnswering Calls at Your Station Monitoring Door TelephonesPlacing Handsfree Answerback Calls on Hold Calls on HoldPlacing Line Appearances or DN Calls on Hold Retrieving Held Calls Using Automatic HoldSwitching Between Calls Isdn Outgoing Calling SubaddressLCD Name/Number Display Message Waiting Cancel LCD MessagesMessaging Create LCD MessagesCancel Messages Waiting Answer Messages WaitingCancel a Called Station Message Waiting Light Set a DN/PhDN Message Waiting LightCancel the Message Waiting Light PhDN/MW Message WaitingActivating Off-hook Announce OCA Handset Calling Using Voice First SignalingOff-hook Call Announce OCA Handset Calling Using Tone Signaling Speaker OCA Using Voice First Signaling Speaker OCA Using Tone SignalingDND Override Override CallsBusy Override Executive OverridePrivacy Override AnnouncementsPrivacy On-Line Privacy Override Privacy Release To deactivate Privacy ReleaseRelease and Answer Speed Dial Storing Station Speed Dial NumbersTo call using SD Stored Station or System Speed Dial CallingTo call using SD access codes Timed RemindersDesktop displays%07,%$$&&..$1*25$773300&&$30$ To cancel a Timed Reminder Toll Restriction OverrideTwo Tandem Line Connection To supervise a tandem call and release it Features Troubleshooting AppendixAppendix Range and Performance Simultaneous Conversation ChannelsSpecifications Radio InterferenceAccess Codes Telephone User Guide for informationWdon + ~ Appendix CO Line Access Codes Feature Access CodesPaging Groups Access Code Paging Group CodesSpeed Dial Access Codes System Codes that Link to Other CodesIndex LCD SP-OCA Index