Radio Shack 43-3857 owner manual Additional Information, Installing the Optional Beltclip

Page 40

Additional Information

Ô NOTES Ô

•If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

•You can use a handset holder (available from your local RadioShack store) to hang the handset on your belt for greater convenience when using a headset.

ADDITIONAL

INFORMATION

INSTALLING THE OPTIONAL BELTCLIP

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it clicks.

To remove the beltclip

Pull both sides of the beltclip to release the tabs from the holes.

HEADSET INSTALLATION

You can connect an optional headset with a 3/32- inch (2.5-mm) plug. Contact RadioShack for a suitable headset.

To connect the headset, open the rubber cover on the side of the handset. Then insert the headset’s plug into the jack. Ô

When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack.

40

Image 40

Contents 4GHz Cordless Phone With Caller ID and Digital Answering MachineContents Information IntroductionFCC Statement FCC Statement Important Safety Instructions Surge ProtectionImportant Caller ID Information InstallationMounting the Phone CONNECTING, Charging and Replacing the Battery Pack On a Desk TopLift the battery pack out of the compartment Changing the Auto Talk and Cidcw Setting Menu OptionsEntering your Area Code Choosing the Dial Mode Setting the LanguageChoosing the Dial Mode Entering your Area CodeOperation Making and Receiving CallsEarpiece Volume Handset Ringer Tone and VolumeTemporarily Mute the Handset Ringer Memory Dialing Traveling OUT-OF-RANGESelecting a Different Channel Flash and Call WaitingPress MEM or REMOTE/SELECT Steps for Entering Names and Special Characters If You Make a Mistake while Entering a Name Memory Dialing from Standby ModeMaking Calls with Memory Dialing Chain Dialing Memory Dialing from Talk ModeEditing a Stored Name AND/OR Phone Number Press END to return to standby mode Testing Stored Emergency Numbers Erasing a Stored Name and Phone NumberONE-TOUCH Speed Dial Storing and Editing the Speed DialMaking Calls with the Speed Dial Deleting the Speed DialYou must subscribe to Caller ID service to use this feature When the Telephone RingsCaller ID Viewing the Caller ID Message List Deleting Information from the Caller ID ListViewing the Caller ID Message List Deleting Information from the Caller ID ListUsing the Caller ID List Deleting a Caller ID MessageDeleting all Caller ID Names/Numbers Calling a Party from the Caller ID ListLong Distance Calls and Area Code Setting/Cancellation Long Distance Calls Area Code Setting CancellationStoring Caller ID Messages in Memory Dialing Storing Caller ID Messages in Memory DialingFeatures Integrated Answering DeviceSetting UP Your Answering System Using the Menu ModeTurning the Answering System Setting the Time Press SET to select the daySetting a Personal Security Code PIN Setting the Ring TimeSelecting the Message Record Time Setting the Message Alert Tone Announce only featureSelecting the Language Press /VOL/SEL or /VOL/SEL to select the desired languageSetting Your Outgoing Message Greeting Preset messageRecording a personal outgoing message Greeting Choosing between the two outgoing messagesAdjusting the speaker volume level Setting the base ringer volumeTemporarily Mute the Base Ringer and the Call Screen Playing your messages Using Your Answering SystemRepeating a message Skipping a message Deleting a messageVoice memo Recording a conversationVoice memo Recording a conversationRemote access away from home Remote OperationTurn on the answering system remotely Remote access with the handset Installing the Optional Beltclip Headset InstallationAdditional Information To attach the beltclipTroubleshooting Problem SolutionSet the record time to either the one minute or four minute Service and Repair CareLimited One-Year Warranty