VTech i6789, i6790 important safety instructions Dial, CONNECTING... is

Page 49

Troubleshooting

Problem

Suggestion

 

 

 

 

 

 

 

Caller ID entries

Although the call log entries you receive are 10 digits, (the area plus the 7-digit number,)

in

 

do not match the

 

some areas, you may need to dial only the seven digits, or a 1 plus the seven digits, or a 1

 

numbers I need to

 

plus the area code plus the seven digits. You can change the number of digits that you dial or

 

dial.

 

store from the call log. While reviewing the call log, press # repeatedly to display these dialing

 

 

 

options for local and long distance numbers before dialing or saving the telephone number.

 

 

 

 

 

CONNECTING... is

De-register all handsets and then register the handsets again (only one handset can be

 

shown in the handset

 

registered at a time).

 

 

display window. Why

 

To de-register all handsets:

 

 

don’t I get a dial tone

 

1. Press and hold FIND HANDSET on the main telephone base for four seconds.

 

 

when I try to use this

 

2. When the IN USE light starts to flash, release the FIND HANDSET button.

 

 

telephone?

 

3. Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds,

 

 

 

 

 

 

all handsets will be de-registered.

 

 

 

 

4. All handsets will show NOT REGISTERED.

 

 

 

 

To register a handset (register one handset at a time):

 

 

 

 

1. Place the handset in the telephone base or a charger that is connected to a power outlet. If

 

 

 

PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds,

 

 

 

lift up the handset and place it in the telephone base or charger again.

 

 

 

 

2. On the telephone base, press and hold FIND HANDSET for four seconds. Release

 

 

 

FIND HANDSET once the IN USE light comes on.

 

 

 

 

After a while, the handset will emit a series of tones. The newly registered handset will be

 

 

 

assigned the lowest handset number not previously assigned to another system handset when

 

 

 

successfully registered. Repeat steps 1 and 2 if the handset is not successfully registered to

 

 

 

the telephone base within two minutes.

 

 

 

 

Repeat the registration procedure for each system handset.

 

 

 

 

 

 

 

 

 

www.vtechphones.com

46

Appendix

Image 49
Contents Need HELP? Table of contents Important safety instructions BatteryTroubleshooting MaintenanceParts checklist InstallationTelephone base installation InstallationInstall handset battery Headset Belt clip & headset optionalBelt clip About caller ID Voicemail serviceIf you subscribe to DSL service Desk/table bracket installation Wall mounting bracket installation optionalHandset layout Telephone settingsFlash SpeakerTelephone base layout Ringer melody Ringer volumeKey tone Settings menuLanguage Dial type Clock settingClear voicemail Wallpaper Display menuContrast Make, answer, and end calls with the handset Basic operationHandset speakerphone MuteIntercom VolumeRinger mute Call waitingTransfer an external call Conference callFLASH, or Answer an incoming call during an intercom call Answering intercom and external callsFind handset Directory Advanced operationStore a directory entry Number Characters by number of key presses Key Space Chart of charactersDial a directory entry Search the directoryEdit a directory entry Delete a directory entry Review the call log Call logDial a call log entry Make CID entries ready to dialSave an entry to the directory Handset display screen messages Delete one or all entriesDisplay Means Dial from redial Redial listDelete a redial entry Message capacity Answering system operationActivate the answering system Answering system setupSet the clock Set base ringer Set number of ringsSet message alert tone Set remote access codeRecord your announcement Outgoing announcementPlay your announcement Delete your announcement Message playbackNew message indication Options during playbackRecord a memo Record and play memosMemo playback Commands in remote standby mode Remote accessCommands during playback mode Message window Handset display screen messages Appendix Handset indicator lights Handset and base indicatorsBattery indicator Base lightsBattery Important safety instructions Problem Suggestion TroubleshootingBase or charger should be on For this to take place Before dialing Troubleshooting My caller ID features are Dial CONNECTING... isAnswering system To one minute for this to take place Operating range MaintenanceAbout cordless telephones WarrantyHow do you get warranty service? FCC Part FCC, Acta and IC regulationsIndustry Canada Rbrc SealTechnical specifications Index Index 91-001070-060-100 User’s manual