VTech v 2656 important safety instructions Installation of Battery Pack in Handset

Page 8

Getting Started

Setup

Installation of Battery Pack in Handset

Follow the steps below:

1.Remove the battery cover by pressing

on the indent and sliding downward.

2.Align the two holes in plug with the

socket pins. Insert the plug into socket. Place the battery pack into the compartment with the wires in one of the bottom corners of the battery pack.

3. Replace the battery cover by sliding it upwards.

4.If the new battery pack is not already charged, place the Handset in the

Base unit, or a remote charging stand, and allow it to charge for 12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient.

The original Handset that is shipped with your v 2656 system will be automatically registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned extension numbers in the following order: HANDSET 2, HANDSET 3, and finally HANDSET 4.

After a Handset battery pack is installed, the Handset will automatically begin SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER BASE ID to register the new Handset.

8

91-005358-050-000 v2656.pmd

8

8/5/2004, 4:51 PM

Image 8

Contents Important Safety Instructions Vtech Communications INC Stop IntroductionParts Check List Handset Layout Base Unit Layout Setup Connecting Power to Base UnitInstallation of Battery Pack in Handset Charging Of Handset Battery Pack Connecting to phone lineChecking for dial tone Case of DifficultyWall Mounting Registration of Additional Handsets Registration and Operation of the v 2600 Accessory HandsetSetup of the v 2600 Accessory Handset Enter Base ID Code Found BaseHandset and Base Indicators Handset IconsBase Leds Icon DescriptionCaller ID Call Waiting ID Soft Menu FunctionsRDL Redial Calls Log Caller ID See To Edit a Number/Name, onHandset Settings LOW Batt Tone preset to onRange Tone preset to on Keypad Tone preset to onTone/Pulse Selection preset to Tone Range Extender preset to AutoRange EXTENDER, then press OK Range Extender menuRegister and Memory MemoryTo Store a Number/Name SaveSearch For and Dial a Number To Search For and Dial a Number NameTo Delete a Number/Name To Edit a Number/Name Handset and Base Operation Making CallsAnswering Calls Mute FunctionFrom Base to ALL Handsets Volume ControlFlash Function Use Indication Switching between the Handset Earpiece and SpeakerphoneHandsfree Speakerphone Operation Transferring Calls Low Battery IndicationConference Calling Audible Indicators Answering System OperationAnswering System Operation Turn Answering System On or OffAbout Mailboxes About AnnouncementsRecord Your Announcement AnsweringSystemOperationTo delete your announcement Answering System Feature SetupTo review your announcement Default setting indicated by Set Security CodeSet Audible Message Alert OffListen to Messages Adjust Playback Volume Press Volume or VolumeDelete Messages Delete a Specific Message Delete All Old Messages in a MailboxRecord a Memo Call ScreeningCounting 1 to 99, flashingSteady for one second 40-99Remote Access Voice MenuHeadset Operation Belt ClipMaintenance Handset Does Not Ring When You Receive a Call Case Of DifficultyPhone Doesnt Work At All No Dial ToneYou Hear Other Calls While Using Your Phone Common Cure For Electronic EquipmentYour Answering System is not recording messages CL is flashing on the Base UnitWarranty Statement What does this limited warranty cover?How long is the limited warranty period? What is not covered by this limited warranty?How do you get warranty service? Other LimitationsFCC Part FCC, Acta and IC RegulationsVTech Communications Inc Rights of the telephone company FCC and Acta InformationRepair instructions IC Industry Canada Programming/testing of emergency numbersHearing aid compatibility Rbrc R Seal Technical Specifications Nominal Effective RangeTable Of Contents Important Safety Instructions Getting StartedBasic Operation Advanced OperationIssue