AT&T 900 MHz user manual If speakerphone conversation sounds distorted, If messages are incomplete

Page 49

IN CASE OF DIFFICULTY

If the caller’s name or phone number is not displayed during Call Waiting:

•You should call your service provider to confirm that you subscribe to a combined Caller ID with Call Waiting service.

•The screen may not display the call information if someone is on an extension phone.

•The Caller ID with Call Waiting feature is inactive during a power interruption.

•Make sure the battery is charged.

•Make sure Caller ID with Call Waiting is turned on (follow the instructions under “Caller ID Feature Setup” in the FEATURE SETUP section of this manual).

If speakerphone conversation sounds distorted:

After the phone is powered up, the speakerphone initializes for about 10–15 seconds the first time it is used. Conversation should be clear after this.

If messages are incomplete:

•If a caller leaves a very long message, part of it may be lost when the system disconnects the call after three minutes.

•If the caller pauses for more than seven seconds, the system stops recording and disconnects the call.

•If the system’s memory becomes full during a message, the system stops recording and disconnects the call.

If you have difficulty hearing messages:

Check the volume setting.

If the system does not answer after the correct number of rings:

•Make sure that the two-digit message window in the base is on. If it is off, press 0[ON/OFF].

•If Toll Saver is on, the number of rings changes to two when you have new messages waiting.

•In some cases, the system may be affected by the ringing system used by the local telephone company.

•If the memory is full or the system is off, the system answers after 10 rings.

48

Image 49

Contents USER’S Manual Advanced American Telephones. All rights reserved Contents About Home and Local Area Codes About Caller ID with Call WaitingBefore You Install InstallationInstall the handset battery Table/Desk and Wall InstallationConnect the telephone line cord Message Window Display for Feature Setup Feature SetupSoftkeys Dial Mode Telephone Feature SetupHandset Ringer Off / Battery Save Handset RingerProgram Home and Local Area Codes Caller ID Feature SetupCaller ID with Call Waiting Call List OptionsAnswering System Feature Setup Ring Select / Toll Saver Select Your AnnouncementAudible Message Alert Priority Call Signal Change Remote Access CodeChange Priority Calling Code Record Your Announcement from the Base Review Feature SettingsSet the Clock Delete an AnnouncementCaller Specific Outgoing Announcement Feature Setup Talking Caller ID Feature SetupAnnouncements Outgoing Local Review ADD Enter Number Done Menu Call ID DIR Directory MEM ANS SYS Delete Done Make Answer, or End a Call Handset VolumeFlash Preview aRedial Telephone OperationTemporary Tone MuteIntercom HoldRecord a Phone Conversation Headset Jack Changing ChannelsAT the Base Speaker Base Ringer VolumeHandset Locator Page/IntercomStore a Number in Memory Telephone MEMORY/DIRECTORYStore a Name with a Memory Number Store a Pause in a Memory NumberReplace a Stored Number View Memory Numbers Store a Number and Name from Call HistoryEdit Memory Numbers Delete Memory NumbersDial a Memory Number from the Handset Priority Ring NumbersDial a Memory Number from the Base About Mailboxes Audible IndicatorsAnnouncement Play/Silent Call Screening/Intercept Answering CallsAnnouncement Bypass Record a MemoFunction Button Listen To, Save & Delete MessagesCL ↔ AO Message Window DisplayConnect with the Answering System Call ScreeningFrom the Cordless Handset From a Touch Tone PhoneFunction Command Remote Access CommandsEnd remote access call Voice Help Menu Audible SignalsIncoming Call History Call WaitingMemory Match Display Dial Review Call HistoryDelete Call Records from Call History Caller ID OperationDelete a Specific Call Record Delete All Call Records Caller ID Display MessagesOperating Range Charge the Handset Battery Pack Battery LifeBatteries Batteries Replace the Handset Battery Pack If the phone does not work at all, check these items first Case of DifficultyIf you have no dial tone To re-initialize the handset and baseIf the phone does not ring when you receive a call If you hear noise or interference when using the phoneIf the caller’s name or phone number is not displayed If messages are incomplete If speakerphone conversation sounds distortedIf you have difficulty hearing messages If your outgoing announcement isn’t clear If CL appears in the Message WindowAnswering System Remote CommandsRemote Command Press