Uniden XCA4500 Connecting the Telephone Cords, Applying Power to the Base Unit

Page 10

Connecting the Telephone Cords

Consider these safety guidelines before connecting the telephone cords:

CAUTION:

∙Never install telephone wiring during a lightning storm.

∙Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected.

∙Use caution when installing or modifying telephone lines.

Applying Power to the Base Unit

The XCA4500 requires a standard electrical outlet (120 volts AC without a switch to interrupt power) and the included AC adapter. Connect the adapter as shown below.

1.Wrap the power cord around the convenient notch on the bottom.

Important: Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards.

2.When power is first applied, the Message Counter LED display flashes P quickly while the system’s memory initializes. When the flashing slows, press the STOP button on the Base Unit.

NEW MESSAGE		Digital Answering
NEW MESSAGE
				P
STOP	REPEAT		PLAY	SKIP
DELETE	ANS ON/OFF	OGM	MEMO	INTERCOM
				PAG E / F I N D

3.The Message Counter LED display turns off, and the time and remaining message record time are announced.

Note: For information about turning the Answering System On/Off, see page 46.

Digital Answering System

NEW MESSAGE
STOP	REPEAT	PLAY	SKIP
DELETE	ANS ON/OFF	OGM	MEMO INTERCOM
			PAG E / F I N D

10

Image 10

Contents Contents Page Important Safety Instructions Page Features IntroductionIncluded with Your XCA4500 Important Electrical Considerations Telephone Line ProblemsRange Radio Interference More Than One Cordless TelephoneSelecting a Location InstallationTelephone Line Outlets Connecting the Telephone Cords Applying Power to the Base UnitInstalling the Backup Battery Desk or Tabletop Installation Page Placement of the Handset Wall InstallationStandard Wall Plate Mounting Page Page Direct Wall Mounting Page Page Setting the Handset Retainer Page Installing the Handset Battery Pack Setting up Your PhoneExtending the Antenna BLK RED Cleaning the Battery Contacts Charging the Handset Battery Pack Initial Battery ChargingContinuous Battery Charging Low Battery IndicatorDuring a Call Standby Mode Adjusting Ringer Controls Setting the Pulse/Tone SwitchHandset Volume Controls Base Volume Controls Automatic Digital Code Security Charge LED will blink to Using Your Phone Making and Receiving CallsChanging Channels, Flash, and Page/Find ChannelsPaging the Base Unit Using the Two-Way IntercomTwo-Way Paging Press Intercom on the Base Unit to answerPaging the Handset Press Intercom on the Base Unit Room Monitor Feature To turn the monitor offProgramming Your Phone Storing a Number in MemoryOnce increases the length of the pause between numbers Storing a Mixed Number with a Pulse System 3300 Storing One-Touch Dialing Numbers Press MDialing a Stored Number Chain DialingErasing a Stored Number Integrated Answering System Turning the Answering System On/Off Answering System SetupHandset Operation To turn the Answeringr System OFF, press Base Operation Setting the ClockPress Handset. r on 30320# Reviewing Time and Day Stamp Preset Messages Setting Your Outgoing Message OGMBase Operation Recording Your Personal OGM Handset Operation TALK/BATT LOW LED lights orangeMessage replays in the Handset receiver Press Hold Selecting a Preset OGM Digital Answering SystemSetting the Calling Party Control Switch Setting the Toll Saver SwitchUsing the Reset Button Using Your Answering System Playing New MessagesTALK/BATT LOW LED goes off Base Operation Press NEW MessagePlaying a Stored Message Press Play Repeating a Message Press r Press 2 to review your messagesPress 1 at anytime to replay a message Skipping a Message RTo eturn. to Standby, press Press Skip at any time to skip to the next message Deleting a Message Press r . .Handset OperationThen an announcement such as Two messages deleted plays Return to Standby Press Release Memo Intercom Deleting All Messages Message Full Indication Digital AnsweringVoice-Guided Help Menu Press rScreening Incoming Calls Leaving a Memo Message NEW Message LED remains on but doesn’t flash Recording a Telephone Conversation Remote Operation Setting Your PIN CodePress # Press Again to return To Standby.r Using a Touch-Tone Phone Your Answering System automatically returns to Standby Telephone Troubleshooting Chart TroubleshootingProblem Suggestion Answering System Troubleshooting Chart Handset SpecificationsBase Unit Answering SystemXCA4500 Precautions Key OGM Review Repeat Key Play Key Skip Key Message Delete KeyStop Key OGM Record Voice Guided Help Key ? PIN/Security Key #Volume Ringer Volume Select Button L Handset Controls and KeysIntercom Button Ringer Volume SwitchBattery LED Memo ButtonOne Year Limited Warranty Covered under one or more of the following U.S. patents