Uniden XCA4500 Low Battery Indicator, Continuous Battery Charging, During a Call Standby Mode

Page 26

2. Make sure the CHARGE LED

lights. If the LED doesn’t light,

check to see that the AC

NEW MESSAGE

Adapter is plugged in and

that the Handset is making

good contact with the Base

IN USE

BATTERY

STOP REPEAT

Unit charging contacts.

Continuous Battery Charging

CHARGE	DELETE	ANS ON/OFF
POWER

For the best battery performance, return the Handset to the Base Unit at the end of the day to keep the battery fully charged.

Low Battery Indicator

When the Battery Pack in the Handset is very low and needs to be charged, the TALK/BATT LOW LED flashes.

	TALK	TALK
		TALK
	1	BATT LOW
	1	2
	1	ABC
	1	2
		2
		7
	GHI	JKL
	4	5
	4	a
	PRS	TUV

7 8

REMOTE

1

DEF

3

3

MNO

6

9

WXY

9

If the TALK/BATT LOW LED begins to flash, the phone is programmed to eliminate its functions to save power. The table below describes what to do to return your phone to normal operation.

During a Call	In Standby Mode

Only the T button operates.	None of the buttons will operate.

The Handset beeps and the	The Handset TALK/BATT LOW LED
TALK/BATT LOW LED flashes once	flashes once every three seconds.
every three seconds.
Complete your call as quickly as	You will not be able to make a call.
possible.

Return the Handset to the Base	Return the Handset to the Base
Unit for charging.	Unit for charging.

Note: Allow 15 to 20 hours without interruption for the Handset to fully recharge.

26

Image 26

Contents Contents Page Important Safety Instructions Page Features IntroductionIncluded with Your XCA4500 Range Telephone Line ProblemsImportant Electrical Considerations Radio Interference More Than One Cordless TelephoneTelephone Line Outlets InstallationSelecting a Location Connecting the Telephone Cords Applying Power to the Base UnitInstalling the Backup Battery Desk or Tabletop Installation Page Standard Wall Plate Mounting Wall InstallationPlacement of the Handset Page Page Direct Wall Mounting Page Page Setting the Handset Retainer Page Extending the Antenna Setting up Your PhoneInstalling the Handset Battery Pack BLK RED Cleaning the Battery Contacts Charging the Handset Battery Pack Initial Battery ChargingDuring a Call Standby Mode Low Battery IndicatorContinuous Battery Charging Handset Volume Controls Setting the Pulse/Tone SwitchAdjusting Ringer Controls Base Volume Controls Automatic Digital Code Security Charge LED will blink to Using Your Phone Making and Receiving CallsChanging Channels, Flash, and Page/Find ChannelsPaging the Base Unit Using the Two-Way IntercomTwo-Way Paging Press Intercom on the Base Unit to answerPaging the Handset Press Intercom on the Base Unit Room Monitor Feature To turn the monitor offProgramming Your Phone Storing a Number in MemoryOnce increases the length of the pause between numbers Storing a Mixed Number with a Pulse System 3300 Storing One-Touch Dialing Numbers Press MDialing a Stored Number Chain DialingErasing a Stored Number Integrated Answering System Handset Operation Answering System SetupTurning the Answering System On/Off To turn the Answeringr System OFF, press Press Handset. r on Setting the ClockBase Operation 30320# Reviewing Time and Day Stamp Base Operation Setting Your Outgoing Message OGMPreset Messages Recording Your Personal OGM Handset Operation TALK/BATT LOW LED lights orangeMessage replays in the Handset receiver Press Hold Selecting a Preset OGM Digital Answering SystemSetting the Calling Party Control Switch Setting the Toll Saver SwitchUsing the Reset Button Using Your Answering System Playing New MessagesTALK/BATT LOW LED goes off Base Operation Press NEW MessagePlaying a Stored Message Press Play Repeating a Message Press r Press 2 to review your messagesPress 1 at anytime to replay a message Skipping a Message RTo eturn. to Standby, press Press Skip at any time to skip to the next message Deleting a Message Press r . .Handset OperationThen an announcement such as Two messages deleted plays Return to Standby Press Release Memo Intercom Deleting All Messages Message Full Indication Digital AnsweringVoice-Guided Help Menu Press rScreening Incoming Calls Leaving a Memo Message NEW Message LED remains on but doesn’t flash Recording a Telephone Conversation Press # Setting Your PIN CodeRemote Operation Press Again to return To Standby.r Using a Touch-Tone Phone Your Answering System automatically returns to Standby Problem Suggestion TroubleshootingTelephone Troubleshooting Chart Answering System Troubleshooting Chart Handset SpecificationsBase Unit Answering SystemXCA4500 Precautions Key OGM Review Repeat Key Play Key Skip Key Message Delete KeyStop Key OGM Record Voice Guided Help Key ? PIN/Security Key #Volume Ringer Volume Select Button L Handset Controls and KeysIntercom Button Ringer Volume SwitchBattery LED Memo ButtonOne Year Limited Warranty Covered under one or more of the following U.S. patents