Uniden XCA4500 important safety instructions Important Safety Instructions

Page 3

Important Safety Instructions

When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without liquid or aerosol cleaners.

4.Do not use this product near water; for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

5.Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the unit.

6.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be damaged by persons walking on it.

9.Do not overload wall outlets and extension cords, as this can result in the risk of fire or electric shock.

10.Never push objects of any kind into this product through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

11.To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.

3

Image 3
Contents Contents Page Important Safety Instructions Page Introduction FeaturesIncluded with Your XCA4500 Telephone Line Problems Important Electrical ConsiderationsRange More Than One Cordless Telephone Radio InterferenceInstallation Selecting a LocationTelephone Line Outlets Applying Power to the Base Unit Connecting the Telephone CordsInstalling the Backup Battery Desk or Tabletop Installation Page Wall Installation Placement of the HandsetStandard Wall Plate Mounting Page Page Direct Wall Mounting Page Page Setting the Handset Retainer Page Setting up Your Phone Installing the Handset Battery PackExtending the Antenna BLK RED Cleaning the Battery Contacts Initial Battery Charging Charging the Handset Battery PackLow Battery Indicator Continuous Battery ChargingDuring a Call Standby Mode Setting the Pulse/Tone Switch Adjusting Ringer ControlsHandset Volume Controls Base Volume Controls Automatic Digital Code Security Charge LED will blink to Making and Receiving Calls Using Your PhoneChannels Changing Channels, Flash, and Page/FindPress Intercom on the Base Unit to answer Using the Two-Way IntercomTwo-Way Paging Paging the Base UnitPaging the Handset Press Intercom on the Base Unit To turn the monitor off Room Monitor FeatureStoring a Number in Memory Programming Your PhoneOnce increases the length of the pause between numbers Storing a Mixed Number with a Pulse System 3300 Press M Storing One-Touch Dialing NumbersChain Dialing Dialing a Stored NumberErasing a Stored Number Integrated Answering System Answering System Setup Turning the Answering System On/OffHandset Operation To turn the Answeringr System OFF, press Setting the Clock Base OperationPress Handset. r on 30320# Reviewing Time and Day Stamp Setting Your Outgoing Message OGM Preset MessagesBase Operation TALK/BATT LOW LED lights orange Recording Your Personal OGM Handset OperationMessage replays in the Handset receiver Press Hold Digital Answering System Selecting a Preset OGMSetting the Toll Saver Switch Setting the Calling Party Control SwitchUsing the Reset Button Playing New Messages Using Your Answering SystemBase Operation Press NEW Message TALK/BATT LOW LED goes offPlaying a Stored Message Press Play Press r Press 2 to review your messages Repeating a MessagePress 1 at anytime to replay a message Skipping a Message RTo eturn. to Standby, press Press Skip at any time to skip to the next message Press r . .Handset Operation Deleting a MessageThen an announcement such as Two messages deleted plays Return to Standby Press Release Memo Intercom Deleting All Messages Digital Answering Message Full IndicationPress r Voice-Guided Help MenuScreening Incoming Calls Leaving a Memo Message NEW Message LED remains on but doesn’t flash Recording a Telephone Conversation Setting Your PIN Code Remote OperationPress # Press Again to return To Standby.r Using a Touch-Tone Phone Your Answering System automatically returns to Standby Troubleshooting Telephone Troubleshooting ChartProblem Suggestion Answering System Troubleshooting Chart Answering System SpecificationsBase Unit HandsetXCA4500 Precautions Voice Guided Help Key ? PIN/Security Key # Repeat Key Play Key Skip Key Message Delete KeyStop Key OGM Record Key OGM ReviewHandset Controls and Keys Volume Ringer Volume Select Button LMemo Button Ringer Volume SwitchBattery LED Intercom ButtonOne Year Limited Warranty Covered under one or more of the following U.S. patents