Uniden XCA4500 Base Operation, Setting Your Outgoing Message OGM, Preset Messages

Page 49

Base Operation

1.Press STOP.

The speaker beeps, and the Time and Day Stamp is announced followed by the remaining recording time available.

NEW MESSAGE		Digital Answering System
NEW MESSAGE
				0
STOP	REPEAT		PLAY	SKIP
DELETE	ANS ON/OFF	OGM	MEMO	INTERCOM
				PAG E / F I N D

Setting Your Outgoing Message (OGM)

When you receive a call, the Answering System answers and automatically plays either a preset message or your personal OGM.

Preset Messages

The XCA4500 has two messages programmed in its memory. If the

REC TIME/ANN-1switch is in the right position, the first preset message below plays, and all incoming messages are limited to one minute. If the switch is set in the left position, (i.e., the “Announce Only” position) the second message below plays, and no incoming messages are recorded.

∙Hello. No one is available to take your call. Please leave your message after the tone.

∙Hello. No one is available to take your call.

REC TIME

ANN-1

RING SW PULSE-TONE CPC

2-5-TSOFF-ON

REC TIME RING VOL ANN-1 OFF-LO-HI TEL-LINE

RESET DC IN 9V

+ -

Note: If the REC TIME/ANN-1switch is in the “Announce Only” position, the Message Counter LED displays an A when the system is in Standby.

49

Image 49

Contents Contents Page Important Safety Instructions Page Introduction FeaturesIncluded with Your XCA4500 Important Electrical Considerations Telephone Line ProblemsRange More Than One Cordless Telephone Radio InterferenceSelecting a Location InstallationTelephone Line Outlets Applying Power to the Base Unit Connecting the Telephone CordsInstalling the Backup Battery Desk or Tabletop Installation Page Placement of the Handset Wall InstallationStandard Wall Plate Mounting Page Page Direct Wall Mounting Page Page Setting the Handset Retainer Page Installing the Handset Battery Pack Setting up Your PhoneExtending the Antenna BLK RED Cleaning the Battery Contacts Initial Battery Charging Charging the Handset Battery PackContinuous Battery Charging Low Battery IndicatorDuring a Call Standby Mode Adjusting Ringer Controls Setting the Pulse/Tone SwitchHandset Volume Controls Base Volume Controls Automatic Digital Code Security Charge LED will blink to Making and Receiving Calls Using Your PhoneChannels Changing Channels, Flash, and Page/FindTwo-Way Paging Using the Two-Way IntercomPaging the Base Unit Press Intercom on the Base Unit to answerPaging the Handset Press Intercom on the Base Unit To turn the monitor off Room Monitor FeatureStoring a Number in Memory Programming Your PhoneOnce increases the length of the pause between numbers Storing a Mixed Number with a Pulse System 3300 Press M Storing One-Touch Dialing NumbersChain Dialing Dialing a Stored NumberErasing a Stored Number Integrated Answering System Turning the Answering System On/Off Answering System SetupHandset Operation To turn the Answeringr System OFF, press Base Operation Setting the ClockPress Handset. r on 30320# Reviewing Time and Day Stamp Preset Messages Setting Your Outgoing Message OGMBase Operation TALK/BATT LOW LED lights orange Recording Your Personal OGM Handset OperationMessage replays in the Handset receiver Press Hold Digital Answering System Selecting a Preset OGMSetting the Toll Saver Switch Setting the Calling Party Control SwitchUsing the Reset Button Playing New Messages Using Your Answering SystemBase Operation Press NEW Message TALK/BATT LOW LED goes offPlaying a Stored Message Press Play Press r Press 2 to review your messages Repeating a MessagePress 1 at anytime to replay a message Skipping a Message RTo eturn. to Standby, press Press Skip at any time to skip to the next message Press r . .Handset Operation Deleting a MessageThen an announcement such as Two messages deleted plays Return to Standby Press Release Memo Intercom Deleting All Messages Digital Answering Message Full IndicationPress r Voice-Guided Help MenuScreening Incoming Calls Leaving a Memo Message NEW Message LED remains on but doesn’t flash Recording a Telephone Conversation Remote Operation Setting Your PIN CodePress # Press Again to return To Standby.r Using a Touch-Tone Phone Your Answering System automatically returns to Standby Telephone Troubleshooting Chart TroubleshootingProblem Suggestion Answering System Troubleshooting Chart Base Unit SpecificationsHandset Answering SystemXCA4500 Precautions Stop Key OGM Record Repeat Key Play Key Skip Key Message Delete KeyKey OGM Review Voice Guided Help Key ? PIN/Security Key #Handset Controls and Keys Volume Ringer Volume Select Button LBattery LED Ringer Volume SwitchIntercom Button Memo ButtonOne Year Limited Warranty Covered under one or more of the following U.S. patents