Motorola DR 3000 service manual RF/DC Retention Clips Removal

Page 36

5-12

Disassembly/Reassembly Procedures: Transmit and Receive Radio Disassembly — Detailed

 

 

3.Remove the accessory connector from the radio assembly by inserting a flat-blade screwdriver into the slot on the side of the connector as shown in Figure 5-8.

!The accessory connector should never be removed when the cover is still assembled to the radio.

C a u t i o n

Flat-blade

Screwdriver

AccessorySlot

Connector

Figure 5-8. Accessory Connector Removal

4.Remove the RF/DC retention clips by gently prying them out with a flat-blade screwdriver as shown in Figure 5-9.

RF/DC Retention Clips

Flat-blade

Screwdriver

Flat-blade

Screwdriver

Figure 5-9. RF/DC Retention Clips Removal

February 21, 2007

6866576D03-A

Image 36
Contents Mototrbo Repeater UHF Range 1 Mototrbo Repeater Product Safety and RF Exposure Compliance ForewordDocument History February 21 Table of Contents Chapter Basic Troubleshooting Appendix a Emea Regional Warranty, Service and SupportGlossary Glossary-1 List of Figures List of Tables Related Publications Introduction Notations Used in This ManualRepeater Description Mototrbo Repeater Model Numbering Scheme AA MModel Description MDM27QPR9JA7ANSpecifications UHF1Transmitter Introduction Specifications Test Equipment and Service Aids Recommended Test EquipmentService Aids Programming CablesWire Diagram Test Equipment and Service Aids Programming Cables Transceiver Performance Testing SetupGeneral AM, CW, FM FMSinad Repeater Tuning and Programming Customer Programming Software SetupRepeater Tuning Setup ACC USBDisassembly/Reassembly Procedures Preventive MaintenanceCleaning Procedures InspectionSafe Handling of Cmos and Ldmos Devices U t i o nRepair Procedures and Techniques General Lead Free Solder Paste Part Number ListDisassembly Procedures Detailed Disassembly of CoverDisassembling and Reassembling the Repeater General Disassembly of Repeater Indicator Board Disassembly of Fan Repeater Indicator Board DisassemblyTx Radio Disassembly Removing Transmit RadioRemoving Thermal Pad and Heatsink Receive Radio Removal Disassembly of Receive Radio Disassembly of Connector Board AssemblyDisassembly of Power Supply Transmit and Receive Radio Disassembly Detailed Transceiver Board and Receiver Board RemovalRF/DC Retention Clips Removal 10. Transceiver Board Removal Transmit and Receive Radio Reassembly Detailed 12. Transceiver Board with Thermal PadsTransceiver Board and Receiver Board Reassembly OccurRF/DC Retention Clips17. Assembling of PA Pad and O-ring 18. Assembling Die Cast Cover onto Chassis Thermal Pad Replacement Procedure 19. Screw Sequence to Tighten Die Cast Cover22. Placing Thermal Pads on PA and Transistor Components Reassembly of Power Supply Reassembly of Receive RadioReassembly of Connector Board Assembly Reassembly of the Receive Bracket Assembly to the EnclosureReassembly of Transmit Radio Replacing the Thermal Pad and HeatsinkReassembly of Fan Reassembly of Repeater Indicator BoardReassembly of Cover Repeater Exploded Mechanical Views and Parts Lists 24. Repeater Assembly Exploded View25. Receive Bracket and Radio Assembly Exploded View 6866576D03-A Torque Chart Disassembly/Reassembly Procedures Torque Chart Basic Troubleshooting Replacement Service Kit ProceduresHigh Power RF Precaution LED Indicator Descriptions LEDWarranty and Service Support Warranty Period and Return InstructionsAfter Warranty Period European Radio Support Centre Ersc Piece PartsTechnical Support Further Assistance From MotorolaEmea Regional Warranty, Service and Technical Support Glossary TOT TPLUHF VIP@6866576D03@