Motorola DR 3000 service manual Rf/Dc, Retention Clips

Page 40

5-16	Disassembly/Reassembly Procedures: Transmit and Receive Radio Reassembly — Detailed

2.Insert the RF/DC retention clips and fully seat them. The DC clip should be inserted first to properly locate the transceiver board. Refer to Figure 5-15.

RF/DC

Retention Clips

Figure 5-15. Inserting RF/DC Retention Clips

3.Insert the accessory connector into the radio assembly and press into place until the connector is flushed with the chassis. Refer to Figure 5-16.

Accessory

Connector

Figure 5-16. Inserting Accessory Connector

February 21, 2007

6866576D03-A

Image 40

Contents Mototrbo Repeater UHF Range 1 Mototrbo Repeater Product Safety and RF Exposure Compliance ForewordDocument History February 21 Table of Contents Appendix a Emea Regional Warranty, Service and Support Chapter Basic TroubleshootingGlossary Glossary-1 List of Figures List of Tables Related Publications Notations Used in This Manual IntroductionRepeater Description Mototrbo Repeater Model Numbering Scheme AA MModel Description MDM27QPR9JA7ANSpecifications UHF1Transmitter Introduction Specifications Test Equipment and Service Aids Recommended Test EquipmentService Aids Programming CablesWire Diagram Test Equipment and Service Aids Programming Cables Transceiver Performance Testing SetupGeneral AM, CW, FM FMSinad Repeater Tuning and Programming Customer Programming Software SetupRepeater Tuning Setup ACC USBDisassembly/Reassembly Procedures Preventive MaintenanceCleaning Procedures InspectionSafe Handling of Cmos and Ldmos Devices U t i o nRepair Procedures and Techniques General Lead Free Solder Paste Part Number ListDisassembly of Cover Disassembly Procedures DetailedDisassembling and Reassembling the Repeater General Disassembly of Repeater Indicator Board Disassembly of Fan Repeater Indicator Board DisassemblyTx Radio Disassembly Removing Transmit RadioRemoving Thermal Pad and Heatsink Receive Radio Removal Disassembly of Connector Board Assembly Disassembly of Receive RadioDisassembly of Power Supply Transmit and Receive Radio Disassembly Detailed Transceiver Board and Receiver Board RemovalRF/DC Retention Clips Removal 10. Transceiver Board Removal Transmit and Receive Radio Reassembly Detailed 12. Transceiver Board with Thermal PadsTransceiver Board and Receiver Board Reassembly OccurRF/DC Retention Clips17. Assembling of PA Pad and O-ring 18. Assembling Die Cast Cover onto Chassis Thermal Pad Replacement Procedure 19. Screw Sequence to Tighten Die Cast Cover22. Placing Thermal Pads on PA and Transistor Components Reassembly of Power Supply Reassembly of Receive RadioReassembly of Connector Board Assembly Reassembly of the Receive Bracket Assembly to the EnclosureReassembly of Transmit Radio Replacing the Thermal Pad and HeatsinkReassembly of Repeater Indicator Board Reassembly of FanReassembly of Cover Repeater Exploded Mechanical Views and Parts Lists 24. Repeater Assembly Exploded View25. Receive Bracket and Radio Assembly Exploded View 6866576D03-A Torque Chart Disassembly/Reassembly Procedures Torque Chart Replacement Service Kit Procedures Basic TroubleshootingHigh Power RF Precaution LED Indicator Descriptions LEDWarranty Period and Return Instructions Warranty and Service SupportAfter Warranty Period European Radio Support Centre Ersc Piece PartsTechnical Support Further Assistance From MotorolaEmea Regional Warranty, Service and Technical Support Glossary TOT TPLUHF VIP@6866576D03@