HTC PDA PHONE II, Andes service manual Connector, Back up battery replacement, Pad

Page 30

6.4 Connector, Back up battery replacement.

If you are authorized by HTC for component replacement, you could do below replacement with following notice:

	Soldering		Back up battery replacement.
			In case of back up battery defective, and
	pad		In case of back up battery defective, and
			need to be replaced, please be noticed to
			soldering requirement:
			1. Soldering Spec must be within 350 °C
			/ 5 seconds.
			2. Never touch the two pin in short
			circuit ,release one by one.
			Warranty Seal (Security Label)
			Be sure to apply new Warranty seal once
			the unit has been repaired before sending
			back to customer.
			P/N: 77H00083-00

In case of MB replacement, since the IMEI has to follow new MB IMEI, repair site is required to re-print Regulatory label to change IMEI no, but Serial No. should remain unchanged.

Put the Battery into its place and lock it.

HTC confidential

© 2001, HTC Corporation. All rights reserved.

TOTAL 77 CONT.ON. 31 PAGE NO. 30

Image 30

Contents For PDA Phone Andes APP´D Table of contents 4END Introduction ContainsSpecification of AC Adapter GSM/GPRS Functional BlockGPRS/GSM 400MHzTotal 77 CONT.ON page no Total 77 CONT.ON page no TTE System Block Diagram Main unit Regulatory label on the rear housing of main unit LabelingLabel example 01 ~TBD Servicing Tools Assembling and Disassembling PDA PhoneTotal 77 CONT.ON page no Total 77 CONT.ON page no Total 77 CONT.ON page no Use tweezers to remove the Vibrator 72H00401-00 Total 77 CONT.ON page no 72H00411-00 MB Pre-assemblyGasket on shielding cover Black poron of Send/End buttonBlack poron for volume button PN of this poron is 76H00483-00Total 77 CONT.ON page no Total 77 CONT.ON page no Antenna Assembly 72H00339-00N72H00338-00 Warranty Seal Security Label FIX Antenna Cover77H00083-00 Test Camera Replacement assemby Connector, Back up battery replacement PadProblem Diagnostics List of Test JigsDiagnostic Program Clean Talk TimeHow to select test item Stop on failChecksum Refurbishment Total 77 CONT.ON page no To Main battery To PC Com Port Voltage 2.5 Criteria for Eeprom Block 1 Status Criteria on running Run Down Test Program B2. ProcedureB1. Requirement Capacity ≧ 50 %Current consumption measurement Fixture requirementReady for testing Unit is turn off and no display Single Single dotsBright dots Dark dotsForeign Scratch Or lints Power Off statusAll allowable defect dots Scratch, Object11.RF 11.1RF Test RequirementRF Antenna Test Spec RF Antenna SpecGSM 900 Transmitter Test DCS 1800 Receiver Test OS Upgrade and GSM code Upgrade Execute RUU Next Total 77 CONT.ON page no Done Following is the complete procedure for SD reflash Execute MTTY.exe and set into USB PortSerial V1.02 Following display will be shown on PC display … Then press ENTER, following display will be shown 100% Checksum is OK HTC confidential SD Download Sections=3 Press Power To Flash…… Once it is Done, display will show Classification of Non-Conformity Troubleshooting & Repair －Ａ．Touch Panel Does Not Respond to Screen Tap－B．Buttons Do Not Respond －A．SD Card cannot be used －A．Data Retention related problem －B．Battery discharges quickly even after fully charged －A．No Recorded Sound or Distorted sound Exploded Diagrams & Spare part list Spare part list Spare Part List with Picture 72H00339-00 75H00313-00 Appendix Customer, Retailer MisjudgmentHTC confidential FTP Repair Troubleshooting Guide Flow Total 77 CONT.ON. F page no